Does the Holosun 407C X2 fit the Shadow Systems MR920?
Yes, the Holosun 407C X2 mounts straight to the Shadow Systems MR920 with no adapter plate; the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Direct mount
The slide is cut for this footprint, so the optic bolts straight on.
What to buy
- Optic
- Holosun 407C X2 ($150–300)
- Plate
- None: it mounts straight to the slide.
- Screws
- Not on file: Shadow Systems supplies the screws in its optic kit, from the optic's or plate's box. Blue threadlocker, never red.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: co-witnesses (estimated, why).
- All in
- $150–300 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Optic → slide
- Optic kit
- screws 1 (V2/X2 models), spacer A, at the rear of the recessFrom Shadow Systems, MR920 / MR920L / XR920 / DR920 / DR920P optic-fit table ↗; Shadow Systems, Pistol Manual (updated 10-22), optic mounting pp. 14-19 ↗, checked against them October 1, 2026 (the optic-fit table, torque and the plates the maker does not sell).
- Thread
- Not on file: Shadow Systems supplies the screws in its optic kitNot on file. What would settle it.
- Torque
- 10–20 in-lbFrom Shadow Systems, Pistol Manual (updated 10-22), optic mounting pp. 14-19 ↗, checked against it October 1, 2026 (the optic-fit table, torque and the plates the maker does not sell).
- Driver
- T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Holosun 407C X2 on the Shadow Systems MR920, Optic to slide: optic kit screws 1 (V2/X2 models), spacer A, at the rear of the recess; thread not on file; torque 10–20 in-lb; driver T10 / T15. Source: Shadow Systems, MR920 / MR920L / XR920 / DR920 / DR920P optic-fit table (https://shadowsystemscorp.com/wp-content/uploads/opticfit-mr.jpg), checked 2026-10-01; Shadow Systems, Pistol Manual (updated 10-22), optic mounting pp. 14-19 (https://shadowsystemscorp.com/wp-content/uploads/Shadow_Pistol_Manual_updated-10-22.pdf), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407c-x2-on-shadow-systems-mr920/#joint-optic-slide
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Shadow Systems MR920
- Optic
- Holosun 407C X2
- Footprint
- Trijicon RMR
- Slide
- Shadow Systems multi-optic cut (MR920, DR920, XR920)
- Mount
- Direct mount
Parts to order
| 1 × | Holosun 407C X2Trijicon RMR footprint · 2 MOA | $150–300 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only | $150–300 |
Where to buy
| Holosun 407C X2Trijicon RMR footprint | Holosun — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Optic → slide | Not on file: Shadow Systems supplies the screws in its optic kit | Shadow's optic kit, taped inside the pistol box lid: screws 1 (V2/X2 models) in Shadow's optic-fit table; spacer A, at the rear of the recess, is optional. The optic bolts straight to the slide with nothing underneath, on Shadow's own screws rather than the ones in the optic's box. Shadow says to put threadlocker on the threads only, never in the slide's holes. |
On the bench before you start
- Torque wrench — covering 20 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the cover plate and set it aside with its screws.
- Degrease the slide cut and the optic base.
- Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
- Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Shadow Systems MR920 with other optics
Direct (cross-fit)6
Plate1
Every optic on the Shadow Systems MR920, and how each mounts
The Holosun 407C X2 on other pistols
Direct3
Plate in box8
Plate11
By serial1
Sources for this page (3)
- Slide Shadow Systems, Pistol Manual (updated 10-22), optic mounting pp. 14-19 ↗
- Slide Shadow Systems, patented multi-footprint optic cut ↗
- Optic Holosun, HS407C-X2 ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Holosun 407C X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Shadow Systems MR920’s slide: the optic-fit table, torque and the plates the maker does not sell checked against Shadow Systems' optic cut page (the CR920 and MR920 optic-fit tables), its pistol manual and C&H Precision's own CR920 listings on October 1, 2026.