Home / Pistols / GLOCK 19 Gen5 MOS / Holosun 407C X2

Does the Holosun 407C X2 fit the GLOCK 19 Gen5 MOS?

Yes, the Holosun 407C X2 fits the GLOCK 19 Gen5 MOS on a plate that ships with the pistol (MOS Plate 02); the optic is the only part to buy.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Fits on the plate in the box

The MOS Plate 02 that ships with the pistol adapts the slide to this footprint. Aftermarket plates are listed below too.

What to buy

Optic
Holosun 407C X2 ($150–300)
Plate
None to buy: the MOS Plate 02 ships with the pistol. Look in the box.
Screws
Look in the pistol's box with the plates; if there are none, buy a pair of 6-32 UNC screws short enough for this plate.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
All in
$150–300 approximate street prices, September 2026
Two other plates fit
  • V4 MIL/LEO → Trijicon RMR / SRO / Holosun 407C / 507C / 508TC&H Precision ↗$25–60Sits lower than the factory plate and is the usual upgrade when a factory plate keeps loosening. Optic screws go into steel T-nuts in the plate; screws for each optic come with it.Plate screws M3 · optic screws 4-40 (into the plate's T-nuts) · both at 12–15 in-lb (C&H)
  • Type A / Type BOptics Spot$25–60Type A covers RMSc / DPP / Docter; Type B covers RMR / RTS2.
Is yours a MOS?A MOS slide has a flat cover plate held on by two screws, just in front of the rear sight, and the item number on its box and paperwork ends in MOS. No cover plate means no optic cut, and none of this page applies: see the non-MOS GLOCK page instead.
SlideGLOCK MOS — standard & full size
Optic footprintTrijicon RMR
Screws and torque below are forMOS Plate 02 (GLOCK factory); other plates list their own above
Optic screws6-32 UNC · T10 / T15
Optic torqueper plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Plate to slide13.1 in-lb (1.5 Nm)
Cost to mount$150–300

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it, for the MOS Plate 02. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
M3From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
Torque
13.1 in-lb (1.5 Nm)From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).

Cite this joint The Holosun 407C X2 on the GLOCK 19 Gen5 MOS, Plate to slide: thread M3; torque 13.1 in-lb (1.5 Nm). Source: GLOCK, accompanying sheet for MOS adapter plates (10/22) (https://eu.glock.com/en/-/media/Global/EU/GLOCK-GmbH-2019/ContactandSupport/Download-Area/Instruction_MOS_Adapter_Plate.ashx), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/holosun-407c-x2-on-glock-19-gen5-mos/#joint-plate-slide

Optic → plate

Thread
6-32 UNCFrom GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
Torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
Driver
T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Holosun 407C X2 on the GLOCK 19 Gen5 MOS, Optic to plate: thread 6-32 UNC; torque not on file; driver T10 / T15. Source: GLOCK, accompanying sheet for MOS adapter plates (10/22) (https://eu.glock.com/en/-/media/Global/EU/GLOCK-GmbH-2019/ContactandSupport/Download-Area/Instruction_MOS_Adapter_Plate.ashx), checked 2026-09-30. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407c-x2-on-glock-19-gen5-mos/#joint-optic-plate

Published for this exact pairing
  • Night Fision · absolute · front .469 / rear .494 in
  • Night Fision · lower 1/3 · front .330 / rear .353 in
  • Night Fision · lower 1/5 · front .290 / rear .313 in
Heights are front / rear in inches, as each sight maker measures its own sights. That's not a deck height, and it doesn't compare across makers to the thousandth. Absolute puts the front sight level with the dot; lower 1/3 and lower 1/5 sit it lower in the window. A sight maker sells a handful of fixed heights, so optics of similar height share one set: the same figures under two optics are the maker's chart saying so, not a copy.Night Fision — co-witness chart for GLOCK 17/19/26/34/45 ↗
With the sights already on itStandard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. The published heights are for aftermarket sight sets, not factory irons, so "no co-witness" is the typical case rather than a guarantee: some optics still show factory-height irons in the lower third or lower fifth of the window.Taller sights made for this optic are the published ones above.
How this slide mounts an opticGLOCK's 9 mm, .40 and .357 MOS slides (Gen4 and Gen5) take its 25.5 mm plates. Recent MOS pistols come with plate 02 (the RMR pattern); earlier ones came with a set, so look in your box before ordering. Plates 01, 03 and 04 are sold separately.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height and the MOS Plate 02. Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
GLOCK 19 Gen5 MOS
Optic
Holosun 407C X2
Footprint
Trijicon RMR
Slide
GLOCK MOS — standard & full size
Mount
Fits on the plate in the box

Parts to order

1 ×Holosun 407C X2Trijicon RMR footprint · 2 MOA$150–300
haveMOS Plate 02GLOCK factory — Trijicon RMR / SRO, Ameriglo, Holosun C-series. Standard MOS pistols ship with this plate. Plates 01, 03 and 04 are factory parts sold separately.in the box
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic only (plate ships with the pistol)$150–300

Where to buy

Holosun 407C X2Trijicon RMR footprintHolosun — this item ↗
MOS Plate 02Ships with the pistol
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideM3Supplied with the pistol, in the box with the cover plate.
Two kinds of short screw come with the pistol: these, for the plate, and the pair already holding the cover plate on the slide. They are different lengths, so keep them apart.
Optic → plate6-32 UNCLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy.

On the bench before you start

  • Torque wrench — covering 13.1 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10 / T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slide13.1 in-lb (1.5 Nm)
Optic torqueper plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Screws6-32 UNC
DriverT10 / T15
Interface2 screws, 2 forward recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Optic screw torque
Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (5)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Holosun 407C X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The GLOCK 19 Gen5 MOS’s slide: plate and optic screw threads, plate screw torque checked against GLOCK's accompanying sheet for MOS adapter plates (10/22) on September 30, 2026. The MOS Plate 02: plate and optic screw threads, plate screw torque checked against GLOCK's accompanying sheet for MOS adapter plates (10/22) on September 30, 2026. Not individually re-checked since it was compiled (September 2026): 2 plates.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.