Does the Trijicon RMR Type 2 fit the GLOCK 19 Gen5 MOS?
Yes, the Trijicon RMR Type 2 fits the GLOCK 19 Gen5 MOS on a plate that ships with the pistol (MOS Plate 02); the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Fits on the plate in the box
The MOS Plate 02 that ships with the pistol adapts the slide to this footprint. Aftermarket plates are listed below too.
- MOS Plate 02GLOCK factory ↗in the boxpriced here and used on the build sheetTrijicon RMR / SRO, Ameriglo, Holosun C-series. Standard MOS pistols ship with this plate. Plates 01, 03 and 04 are factory parts sold separately.Plate screws M3 · optic screws 6-32 UNC · from GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗
What to buy
- Optic
- Trijicon RMR Type 2 ($450–650)
- Plate
- None to buy: the MOS Plate 02 ships with the pistol. Look in the box.
- Screws
- Look in the pistol's box with the plates; if there are none, buy a pair of 6-32 UNC screws short enough for this plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
- All in
- $450–650 approximate street prices, September 2026
Two other plates fit
- V4 MIL/LEO → Trijicon RMR / SRO / Holosun 407C / 507C / 508TC&H Precision ↗$25–60Sits lower than the factory plate and is the usual upgrade when a factory plate keeps loosening. Optic screws go into steel T-nuts in the plate; screws for each optic come with it.Plate screws M3 · optic screws 4-40 (into the plate's T-nuts) · both at 12–15 in-lb (C&H)
- Type A / Type BOptics Spot$25–60Type A covers RMSc / DPP / Docter; Type B covers RMR / RTS2.
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it, for the MOS Plate 02. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M3From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
- Torque
- 13.1 in-lb (1.5 Nm)From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
Cite this joint The Trijicon RMR Type 2 on the GLOCK 19 Gen5 MOS, Plate to slide: thread M3; torque 13.1 in-lb (1.5 Nm). Source: GLOCK, accompanying sheet for MOS adapter plates (10/22) (https://eu.glock.com/en/-/media/Global/EU/GLOCK-GmbH-2019/ContactandSupport/Download-Area/Instruction_MOS_Adapter_Plate.ashx), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-glock-19-gen5-mos/#joint-plate-slide
Optic → plate
- Thread
- 6-32 UNCFrom GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
- Torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Trijicon RMR Type 2 on the GLOCK 19 Gen5 MOS, Optic to plate: thread 6-32 UNC; torque not on file; driver T10 / T15. Source: GLOCK, accompanying sheet for MOS adapter plates (10/22) (https://eu.glock.com/en/-/media/Global/EU/GLOCK-GmbH-2019/ContactandSupport/Download-Area/Instruction_MOS_Adapter_Plate.ashx), checked 2026-09-30. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-glock-19-gen5-mos/#joint-optic-plate
- Dawson Precision · co-witness · front .405 / rear .395 in
- Night Fision · lower 1/3 · front .330 / rear .353 in
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height and the MOS Plate 02. Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- GLOCK 19 Gen5 MOS
- Optic
- Trijicon RMR Type 2
- Footprint
- Trijicon RMR
- Slide
- GLOCK MOS — standard & full size
- Mount
- Fits on the plate in the box
Parts to order
| 1 × | Trijicon RMR Type 2Trijicon RMR footprint · 1.0 / 3.25 / 6.5 MOA | $450–650 |
| have | MOS Plate 02GLOCK factory — Trijicon RMR / SRO, Ameriglo, Holosun C-series. Standard MOS pistols ship with this plate. Plates 01, 03 and 04 are factory parts sold separately. | in the box |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only (plate ships with the pistol) | $450–650 |
Where to buy
| Trijicon RMR Type 2Trijicon RMR footprint | Trijicon — this item ↗ |
| MOS Plate 02 | Ships with the pistol |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M3 | Supplied with the pistol, in the box with the cover plate. Two kinds of short screw come with the pistol: these, for the plate, and the pair already holding the cover plate on the slide. They are different lengths, so keep them apart. |
| Optic → plate | 6-32 UNC | Look in the pistol's box, with the plates. If there are none, buy a pair made for this plate. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — covering 13.1 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The GLOCK 19 Gen5 MOS with other optics
Plate in box3
Every optic on the GLOCK 19 Gen5 MOS, and how each mounts
The Trijicon RMR Type 2 on other pistols
Direct4
Plate in box7
Plate12
By serial1
Sources for this page (6)
- Slide GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗
- Optic Trijicon, RMR spec sheet (PML4014-2) ↗
- Plate GLOCK factory, MOS Plate 02 ↗
- Plate C&H Precision, V4 MIL/LEO → Trijicon RMR / SRO / Holosun 407C / 507C / 508T ↗
- Sights Dawson Precision, fixed co-witness set for GLOCK 17/19 Gen5 MOS with an RMR ↗
- Sights Night Fision, co-witness chart for GLOCK 17/19/26/34/45 ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Trijicon RMR Type 2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The GLOCK 19 Gen5 MOS’s slide: plate and optic screw threads, plate screw torque checked against GLOCK's accompanying sheet for MOS adapter plates (10/22) on September 30, 2026. The MOS Plate 02: plate and optic screw threads, plate screw torque checked against GLOCK's accompanying sheet for MOS adapter plates (10/22) on September 30, 2026. Not individually re-checked since it was compiled (September 2026): 2 plates.