Does the Trijicon RMR Type 2 fit the Heckler & Koch VP9 Optics Ready?
Yes, the Trijicon RMR Type 2 fits the Heckler & Koch VP9 Optics Ready with an adapter plate; two plates fit, and the cheapest is the HK Optics Plate #2 (50254262), a HK factory part.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
The slide isn't cut for this pattern. 2 plates adapt it, listed below. The plate supplies the recoil posts the optic sits on.
- HK Optics Plate #2 (50254262)HK factory ↗$25–60priced here and used on the build sheetHK says "Trijicon RMR and Holosun", and not the Holosun 507K or the Trijicon RMRcc. It does not name the SRO or any other maker's RMR-pattern optic, so they are not listed here; C&H's plate names the SRO.Plate screws M4 · optic screws not in HK factory's listing · optic screws at per the optic maker (HK's manual gives no figure) · from Heckler & Koch USA, VP Series operator's manual, all models and calibers ↗
What to buy
- Optic
- Trijicon RMR Type 2 ($450–650)
- Plate
- The HK Optics Plate #2 (50254262), a HK factory part ($25–60).
- Screws
- per plate maker, not on file here screws. Not stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
- All in
- $475–710 approximate street prices, September 2026
One other plate fits
- VP9 / SFP9 → Trijicon RMR / SRO / Holosun CC&H Precision ↗$25–60C&H packs a set of 4-40 optic screws for each optic it lists, so it fits only those. It says the plate will not work with the Trijicon RCR.Plate screws M4 · optic screws 4-40 (into the plate's T-nuts)
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it, for the HK Optics Plate #2 (50254262). Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M4From Heckler & Koch USA, VP Series operator's manual, all models and calibers ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
- Torque
- 2 Nm (17.7 in-lb, converted)From Heckler & Koch USA, VP Series operator's manual, all models and calibers (VP9 Optic Ready plate options and installation) ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Cite this joint The Trijicon RMR Type 2 on the Heckler & Koch VP9 Optics Ready, Plate to slide: thread M4; torque 2 Nm (17.7 in-lb, converted). Source: Heckler & Koch USA, VP Series operator's manual, all models and calibers (https://hk-usa.com/wp-content/uploads/2025/01/VP-Series-Operator-Manual.pdf), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-heckler-and-koch-vp9-optics-ready/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per the optic maker (HK's manual gives no figure)
- Driver
- T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Trijicon RMR Type 2 on the Heckler & Koch VP9 Optics Ready, Optic to plate: thread not on file; torque per the optic maker (HK's manual gives no figure); driver T10 / T15. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-heckler-and-koch-vp9-optics-ready/#joint-optic-plate
- Night Fision · absolute · front .480 / rear .517 in
- Night Fision · lower 1/3 · front .350 / rear .387 in
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height and the HK Optics Plate #2 (50254262). Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Heckler & Koch VP9 Optics Ready
- Optic
- Trijicon RMR Type 2
- Footprint
- Trijicon RMR
- Slide
- HK VP9 / SFP9 OR plate system
- Mount
- Adapter plate required
Parts to order
| 1 × | Trijicon RMR Type 2Trijicon RMR footprint · 1.0 / 3.25 / 6.5 MOA | $450–650 |
| 1 × | HK Optics Plate #2 (50254262)HK factory — HK says "Trijicon RMR and Holosun", and not the Holosun 507K or the Trijicon RMRcc. It does not name the SRO or any other maker's RMR-pattern optic, so they are not listed here; C&H's plate names the SRO. | $25–60 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $475–710 |
Where to buy
| Trijicon RMR Type 2Trijicon RMR footprint | Trijicon — this item ↗ |
| HK Optics Plate #2 (50254262)HK factory | HK factory — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M4 | The two screws that hold the cover plate on the slide, reused for the plate (HK sells spares, part 50947116, and says to replace them after 2,000 rounds). HK's own instruction is to mount the optic plate with the two screws that hold the cover plate on the Optic Ready slide, so unlike most slides these are the same screws: take the cover plate off, fit the plate with them, and keep the cover plate for when the optic comes off. HK says to use thread locker on these screws, and to replace them with new ones after 2,000 rounds. |
| Optic → plate | per plate maker, not on file here | Not stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — covering 17.7 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Heckler & Koch VP9 Optics Ready with other optics
Plate12
No fit1
Every optic on the Heckler & Koch VP9 Optics Ready, and how each mounts
The Trijicon RMR Type 2 on other pistols
Direct4
Plate in box8
Plate11
By serial1
Sources for this page (7)
- Slide Heckler & Koch USA, VP Series operator's manual, all models and calibers (VP9 Optic Ready plate options and installation) ↗
- Slide Heckler & Koch USA, VP9A1 operator's manual (plates 1 to 7 and the Holosun K and 509T plates, 2 Nm, optic screws to the optic maker's torque) ↗
- Slide Heckler & Koch USA, VP9 Match ↗
- Slide Heckler & Koch USA webshop, Optics Plate #2 for VP9 Optic Ready Models ↗
- Optic Trijicon, RMR spec sheet (PML4014-2) ↗
- Plate C&H Precision, VP9 / SFP9 → Trijicon RMR / SRO / Holosun C ↗
- Sights Night Fision, co-witness chart for HK (not split by model) ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Trijicon RMR Type 2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Heckler & Koch VP9 Optics Ready’s slide: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The HK Optics Plate #2 (50254262): The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The VP9 / SFP9 → Trijicon RMR / SRO / Holosun C: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026.