Does the Holosun EPS Carry fit the Heckler & Koch VP9 Optics Ready?

Yes, the Holosun EPS Carry fits the Heckler & Koch VP9 Optics Ready with an adapter plate; two plates fit, and the cheapest is the VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry from C&H Precision.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

Enclosed emitter

The slide isn't cut for this pattern. 2 plates adapt it, listed below. The plate supplies the recoil posts the optic sits on.

  • VP9 / SFP9 → Holosun EPS / EPS Carry / SCS CarryC&H Precision ↗$25–60priced here and used on the build sheetA separate plate from C&H's 407K / 507K one.Plate screws M4 · optic screws 4-40 (into the plate's T-nuts)

What to buy

Optic
Holosun EPS Carry ($300–450)
Plate
The VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry, from C&H Precision ($25–60).
Screws
4-40 (into the plate's T-nuts), from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: low at best (estimated, why).
All in
$325–510 approximate street prices, September 2026
One other plate fits
  • VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW)EGW ↗$25–60EGW says its plate is comparable to HK's plate #4. It lists the Vortex Defender series, and says the Defender XL needs the screws Vortex provides.Plate screws M4 · optic screws 6-32 (EGW's screws, in the plate) · plate screws at 2 Nm (17.7 in-lb), as EGW quotes HK's figure · optic screws at 15 in-lb (EGW)
Same answer forThe Holosun EPS Carry goes on the Heckler & Koch VP9 Match OR, Heckler & Koch VP9SK Optics Ready and Heckler & Koch SFP9 OR (European VP9) the same way: they share this slide's optic cut.
SlideHK VP9 / SFP9 OR plate system
Optic footprintHolosun K
Screws and torque below are forVP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry (C&H Precision); other plates list their own above
Optic screws4-40 (into the plate's T-nuts) · T10
Optic torqueper plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Plate to slideper plate maker, not on file here (2 Nm (17.7 in-lb, converted) is the slide maker's figure for its own plates, not this one)
Cost to mount$325–510

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it, for the VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
M4From C&H Precision, VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Torque
per plate maker, not on file here (2 Nm (17.7 in-lb, converted) is the slide maker's figure for its own plates, not this one)Not on file. What would settle it.

Cite this joint The Holosun EPS Carry on the Heckler & Koch VP9 Optics Ready, Plate to slide: thread M4; torque not on file. Source: C&H Precision, VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry (https://chpws.com/product/hk-vp9-to-holosun-eps-eps-carry-scs-carry/), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/holosun-eps-carry-on-heckler-and-koch-vp9-optics-ready/#joint-plate-slide

Optic → plate

Thread
4-40 (into the plate's T-nuts)From C&H Precision, VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
Driver
T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Holosun EPS Carry on the Heckler & Koch VP9 Optics Ready, Optic to plate: thread 4-40 (into the plate's T-nuts); torque not on file; driver T10. Source: C&H Precision, VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry (https://chpws.com/product/hk-vp9-to-holosun-eps-eps-carry-scs-carry/), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-eps-carry-on-heckler-and-koch-vp9-optics-ready/#joint-optic-plate

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Low at best. An enclosed emitter on a plate sits tall, so suppressor-height irons land at the very bottom of the window or below it: Night Fision lists its .290 in front sight as a lower 1/5 co-witness for an ACRO P-2 on GLOCK's MOS plate, and taller optics lose them. Sights taller than suppressor height are the usual fix. This optic's window runs small (19.6 × 14.7 mm), so a front sight slightly off the ideal height is more likely to miss it. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
On this modelHK's manual lists the Optic Ready plates as not included with the pistol: it comes with a cover plate over the cut, and the plate is bought separately.
How this slide mounts an opticHK sells the Optic Ready plates separately: its manual lists them as "not included with VP Optic Ready", and HK USA's VP9 Match page says the cut takes "one of five available mounting plates (sold separately)". The slide ships with a cover plate over the cut. HK's plates are numbered: its manual lists plate 01 (Meopta MeoSight III, EOTech MRDS, Noblex Sight III), 02 (Trijicon RMR, Holosun), 03 (C-More STS2), 04 (Leupold DeltaPoint) and 05 (Burris FastFire 2 and 3, Vortex Viper and Venom); HK USA's webshop adds an ACRO plate (6), a Holosun K plate that also lists the Shield RMSc, and a 509T plate. HK names optics one by one, so each of its plates is listed here for the optics it names, not for the whole footprint. C&H and EGW sell plates for more. Source: Heckler & Koch USA, VP9A1 operator's manual (plates 1 to 7 and the Holosun K and 509T plates, 2 Nm, optic screws to the optic maker's torque) ↗; Heckler & Koch USA, VP9 Match ↗; Heckler & Koch USA webshop, Optics Plate #2 for VP9 Optic Ready Models ↗.
About this opticEnclosed emitter in a carry-size body.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height and the VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry. Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Heckler & Koch VP9 Optics Ready
Optic
Holosun EPS Carry
Footprint
Holosun K
Slide
HK VP9 / SFP9 OR plate system
Mount
Adapter plate required

Parts to order

1 ×Holosun EPS CarryHolosun K footprint · 2 / 6 MOA$300–450
1 ×VP9 / SFP9 → Holosun EPS / EPS Carry / SCS CarryC&H Precision — A separate plate from C&H's 407K / 507K one.$25–60
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$325–510

Where to buy

Holosun EPS CarryHolosun K footprintHolosun — this item ↗
VP9 / SFP9 → Holosun EPS / EPS Carry / SCS CarryC&H PrecisionC&H Precision — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideM4Supplied with the plate.
If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths.
Optic → plate4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy.

On the bench before you start

  • Torque wrench — set to the figure in your optic's manual
  • Driver bits — T10, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slideper plate maker, not on file here (2 Nm (17.7 in-lb, converted) is the slide maker's figure for its own plates, not this one)
Optic torqueper plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Screws4-40 (into the plate's T-nuts)
DriverT10
Interface2 screws, 2 forward lugs (rear posts omitted)

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Plate-to-slide torque
Not published for this plate. Use the plate maker's figure.
Optic screw torque
Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (7)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Holosun EPS Carry: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Heckler & Koch VP9 Optics Ready’s slide: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The VP9 / SFP9 → Holosun EPS / EPS Carry / SCS Carry: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW): The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.