Does the Holosun EPS Carry fit the SIG Sauer P365XL?
Yes, the Holosun EPS Carry mounts straight to the SIG Sauer P365XL with no adapter plate, but on M3 or M4 screws: the ones in the optic's box are cut for a different thread.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Direct mount — cross-compatible
Enclosed emitterThe slide is cut for Shield RMSc, and this footprint fits that cut with no adapter.
What to buy
- Optic
- Holosun EPS Carry ($300–450)
- Plate
- None: it mounts straight to the slide.
- Screws
- Buy a pair of M3 or M4 screws: the ones in the optic's box are the wrong thread.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: marginal (estimated, why).
- All in
- $300–450 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Optic → slide
- Thread
- M3 × 0.5 or M4 × 0.7, by slideFrom SIG Sauer, ROMEO-X M4 screw set ↗; SIG Sauer, ROMEO-X M3 & M4 screw kit ↗; SIG Sauer, ROMEOZero operator's manual (REV10) ↗; SIG Sauer, ROMEO-X enclosed Compact and Pro operator's manual (REV10) ↗; SIG Sauer, ROMEOZero-ELITE operator's manual (REV00) ↗, checked against them September 30, 2026 (slide screw thread).
- Torque
- 15 in-lbThe footprint's usual figure, but no document is linked for it here yet. What would settle it.
- Driver
- T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Holosun EPS Carry on the SIG Sauer P365XL, Optic to slide: thread M3 × 0.5 or M4 × 0.7, by slide; torque 15 in-lb; driver T10. Source: SIG Sauer, ROMEO-X M4 screw set (https://www.sigsauer.com/romeo-x-mounting-screw-set-m4-torx.html), checked 2026-09-30; SIG Sauer, ROMEO-X M3 & M4 screw kit (https://www.sigsauer.com/romeox-torx-mounting-screw-kit.html), checked 2026-09-30; SIG Sauer, ROMEOZero operator's manual (REV10) (https://www.sigsauer.com/media/sigsauer/resources/25SIG3823_ROMEOZero_Manual_7405057-01_R10.pdf), checked 2026-09-30; SIG Sauer, ROMEO-X enclosed Compact and Pro operator's manual (REV10) (https://www.sigsauer.com/media/sigsauer/resources/OPERATORS-MANUAL-ROMEO-X-PRO-ENCLOSED-7404948-01-REV10_WEB-FILE.pdf), checked 2026-09-30; SIG Sauer, ROMEOZero-ELITE operator's manual (REV00) (https://www.sigsauer.com/media/sigsauer/resources/OPERATORS_MANUAL_ROMEOZERO_ELITE_7403827-01_REV_00_LR.pdf), checked 2026-09-30. No maker document on file for the torque or driver. Optic Mounting, https://opticmounting.com/fit/holosun-eps-carry-on-sig-sauer-p365xl/#joint-optic-slide
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- SIG Sauer P365XL
- Optic
- Holosun EPS Carry
- Footprint
- Holosun K
- Slide
- SIG P365 optic cut (RMSc pattern)
- Mount
- Direct mount — cross-compatible
Parts to order
| 1 × | Holosun EPS CarryHolosun K footprint · 2 / 6 MOA | $300–450 |
| 1 set | Optic screws, M3 or M4The screws in the optic's box are cut for a different thread. Length depends on the optic; test-fit dry. | — |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only | $300–450 |
Where to buy
| Holosun EPS CarryHolosun K footprint | Holosun — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
One set to buy, listed above; the rest come in the boxes. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Optic → slide | M3 × 0.5 or M4 × 0.7, by slide | Check your slide's thread, then buy screws to match. The slide's tapping decides the screw, not the optic. Start each screw by hand.Thread trapSIG tapped early P365 optic cuts M3 × 0.5 and later ones M4 × 0.7, and sells a screw set for each. The model name doesn't tell you which slide you have; SIG's screw-set page shows both. Your slide is tapped M3 or M4. No date or serial-number rule from the maker says which a slide has, so there is no shortcut. To tell which, turn an M3 screw in by hand only: if it catches and runs in smoothly, the slide is M3; if it wobbles and never bites, the slide is M4. Never put a driver on a screw that won't start by hand. Screws in the box vary by Holosun K model. |
On the bench before you start
- Torque wrench — covering 15 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the cover plate and set it aside with its screws.
- Degrease the slide cut and the optic base.
- Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
- Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The SIG Sauer P365XL with other optics
Direct (cross-fit)2
Every optic on the SIG Sauer P365XL, and how each mounts
The Holosun EPS Carry on other pistols
Direct (cross-fit)6
Plate in box2
Plate20
- GLOCK 19 Gen5 MOS
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- SIG Sauer P320 X-Carry
- GLOCK 17 Gen5 MOS
- GLOCK 48 MOS
- Walther PDP Full Size (1.0)
- GLOCK 45 Gen5 MOS
- GLOCK 26 Gen5 MOS
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- SIG Sauer P320 XCompact
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Walther PDP Compact (1.0)
- CZ P-10 C Optics Ready
- Heckler & Koch VP9 Optics Ready
- Staccato P
- CZ Shadow 2 Optics Ready
- Canik TTI Combat
Sources for this page (6)
- Slide SIG Sauer, ROMEO-X M4 screw set ↗
- Slide SIG Sauer, ROMEO-X M3 & M4 screw kit ↗
- Slide SIG Sauer, ROMEOZero operator's manual (REV10) ↗
- Slide SIG Sauer, ROMEO-X enclosed Compact and Pro operator's manual (REV10) ↗
- Slide SIG Sauer, ROMEOZero-ELITE operator's manual (REV00) ↗
- Optic Holosun, EPS Carry ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Holosun EPS Carry: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The SIG Sauer P365XL’s slide: slide screw thread checked against SIG's ROMEOZero, ROMEOZero-ELITE and ROMEO-X operator's manuals on September 30, 2026.