Home / Pistols / Heckler & Koch VP9 Optics Ready / Vortex Defender-CCW

Does the Vortex Defender-CCW fit the Heckler & Koch VP9 Optics Ready?

Yes, the Vortex Defender-CCW fits the Heckler & Koch VP9 Optics Ready with an adapter plate: the VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) from EGW.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

The slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.

  • VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW)EGW ↗$25–60EGW says its plate is comparable to HK's plate #4. It lists the Vortex Defender series, and says the Defender XL needs the screws Vortex provides.Plate screws M4 · optic screws 6-32 (EGW's screws, in the plate) · plate screws at 2 Nm (17.7 in-lb), as EGW quotes HK's figure · optic screws at 15 in-lb (EGW)

What to buy

Optic
Vortex Defender-CCW ($150–300)
Plate
The VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW), from EGW ($25–60).
Screws
6-32 (EGW's screws, in the plate), from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
All in
$175–360 approximate street prices, September 2026
Same answer forThe Vortex Defender-CCW goes on the Heckler & Koch VP9 Match OR, Heckler & Koch VP9SK Optics Ready and Heckler & Koch SFP9 OR (European VP9) the same way: they share this slide's optic cut.
SlideHK VP9 / SFP9 OR plate system
Optic footprintShield RMSc
Optic screws6-32 (EGW's screws, in the plate) · T10 / T15
Optic torque15 in-lb (EGW)
Plate to slide2 Nm (17.7 in-lb), as EGW quotes HK's figure
Cost to mount$175–360

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
M4From EGW, VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Torque
2 Nm (17.7 in-lb), as EGW quotes HK's figureFrom EGW, VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).

Cite this joint The Vortex Defender-CCW on the Heckler & Koch VP9 Optics Ready, Plate to slide: thread M4; torque 2 Nm (17.7 in-lb), as EGW quotes HK's figure. Source: EGW, VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) (https://egwguns.com/deltapoint-pro-fits-holosun-407k-507k-jpoint-redfield-accelerator-and-optima-sight-for-hk-vp9-optics-ready), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/vortex-defender-ccw-on-heckler-and-koch-vp9-optics-ready/#joint-plate-slide

Optic → plate

Thread
6-32 (EGW's screws, in the plate)From EGW, VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Torque
15 in-lb (EGW)From EGW, VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Driver
T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Vortex Defender-CCW on the Heckler & Koch VP9 Optics Ready, Optic to plate: thread 6-32 (EGW's screws, in the plate); torque 15 in-lb (EGW); driver T10 / T15. Source: EGW, VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW) (https://egwguns.com/deltapoint-pro-fits-holosun-407k-507k-jpoint-redfield-accelerator-and-optima-sight-for-hk-vp9-optics-ready), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/vortex-defender-ccw-on-heckler-and-koch-vp9-optics-ready/#joint-optic-plate

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Usually a low co-witness. A plate raises the optic, so suppressor-height irons ride near the bottom of the window: Night Fision, for one, lists its .290 in front sight as a lower 1/5 co-witness with RMR-class optics on GLOCK's MOS plate. A taller plate can drop them out of view, so check the plate's deck height before ordering sights. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
On this modelHK's manual lists the Optic Ready plates as not included with the pistol: it comes with a cover plate over the cut, and the plate is bought separately.
How this slide mounts an opticHK sells the Optic Ready plates separately: its manual lists them as "not included with VP Optic Ready", and HK USA's VP9 Match page says the cut takes "one of five available mounting plates (sold separately)". The slide ships with a cover plate over the cut. HK's plates are numbered: its manual lists plate 01 (Meopta MeoSight III, EOTech MRDS, Noblex Sight III), 02 (Trijicon RMR, Holosun), 03 (C-More STS2), 04 (Leupold DeltaPoint) and 05 (Burris FastFire 2 and 3, Vortex Viper and Venom); HK USA's webshop adds an ACRO plate (6), a Holosun K plate that also lists the Shield RMSc, and a 509T plate. HK names optics one by one, so each of its plates is listed here for the optics it names, not for the whole footprint. C&H and EGW sell plates for more. Source: Heckler & Koch USA, VP9A1 operator's manual (plates 1 to 7 and the Holosun K and 509T plates, 2 Nm, optic screws to the optic maker's torque) ↗; Heckler & Koch USA, VP9 Match ↗; Heckler & Koch USA webshop, Optics Plate #2 for VP9 Optic Ready Models ↗.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Heckler & Koch VP9 Optics Ready
Optic
Vortex Defender-CCW
Footprint
Shield RMSc
Slide
HK VP9 / SFP9 OR plate system
Mount
Adapter plate required

Parts to order

1 ×Vortex Defender-CCWShield RMSc footprint · 3 / 6 MOA$150–300
1 ×VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW)EGW — EGW says its plate is comparable to HK's plate #4. It lists the Vortex Defender series, and says the Defender XL needs the screws Vortex provides.$25–60
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$175–360

Where to buy

Vortex Defender-CCWShield RMSc footprintVortex — this item ↗
VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW)EGWEGW — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideM4Supplied with the plate.
If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths.
Optic → plate6-32 (EGW's screws, in the plate)Supplied with the plate, not the optic.
Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy.

On the bench before you start

  • Torque wrench — covering 15–17.7 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10 / T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slide2 Nm (17.7 in-lb), as EGW quotes HK's figure
Optic torque15 in-lb (EGW)
Screws6-32 (EGW's screws, in the plate)
DriverT10 / T15
Interface2 screws, 4 recoil lugs (2 front, 2 rear)

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (6)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Vortex Defender-CCW: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Heckler & Koch VP9 Optics Ready’s slide: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The VP9 OR → Holosun K / Shield RMSc / DeltaPoint Pro / Defender (EGW): The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.