Does the Holosun 407C X2 fit the Heckler & Koch VP9 Optics Ready?

Yes, the Holosun 407C X2 fits the Heckler & Koch VP9 Optics Ready with an adapter plate; two plates fit, and the cheapest is the HK Optics Plate #2 (50254262), a HK factory part.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

The slide isn't cut for this pattern. 2 plates adapt it, listed below. The plate supplies the recoil posts the optic sits on.

  • HK Optics Plate #2 (50254262)HK factory ↗$25–60priced here and used on the build sheetHK says "Trijicon RMR and Holosun", and not the Holosun 507K or the Trijicon RMRcc. It does not name the SRO or any other maker's RMR-pattern optic, so they are not listed here; C&H's plate names the SRO.Plate screws M4 · optic screws not in HK factory's listing · optic screws at per the optic maker (HK's manual gives no figure) · from Heckler & Koch USA, VP Series operator's manual, all models and calibers ↗

What to buy

Optic
Holosun 407C X2 ($150–300)
Plate
The HK Optics Plate #2 (50254262), a HK factory part ($25–60).
Screws
per plate maker, not on file here screws. Not stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
All in
$175–360 approximate street prices, September 2026
One other plate fits
  • VP9 / SFP9 → Trijicon RMR / SRO / Holosun CC&H Precision ↗$25–60C&H packs a set of 4-40 optic screws for each optic it lists, so it fits only those. It says the plate will not work with the Trijicon RCR.Plate screws M4 · optic screws 4-40 (into the plate's T-nuts)
Same answer forThe Holosun 407C X2 goes on the Heckler & Koch VP9 Match OR, Heckler & Koch VP9SK Optics Ready and Heckler & Koch SFP9 OR (European VP9) the same way: they share this slide's optic cut.
SlideHK VP9 / SFP9 OR plate system
Optic footprintTrijicon RMR
Screws and torque below are forHK Optics Plate #2 (50254262) (HK factory); other plates list their own above
Optic screwsper plate maker, not on file here · T10 / T15
Optic torqueper the optic maker (HK's manual gives no figure)
Plate to slide2 Nm (17.7 in-lb, converted)
Cost to mount$175–360

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it, for the HK Optics Plate #2 (50254262). Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
M4From Heckler & Koch USA, VP Series operator's manual, all models and calibers ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).
Torque
2 Nm (17.7 in-lb, converted)From Heckler & Koch USA, VP Series operator's manual, all models and calibers (VP9 Optic Ready plate options and installation) ↗, checked against it October 1, 2026 (The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR).

Cite this joint The Holosun 407C X2 on the Heckler & Koch VP9 Optics Ready, Plate to slide: thread M4; torque 2 Nm (17.7 in-lb, converted). Source: Heckler & Koch USA, VP Series operator's manual, all models and calibers (https://hk-usa.com/wp-content/uploads/2025/01/VP-Series-Operator-Manual.pdf), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/holosun-407c-x2-on-heckler-and-koch-vp9-optics-ready/#joint-plate-slide

Optic → plate

Thread
per plate maker, not on file hereNot on file. What would settle it.
Torque
per the optic maker (HK's manual gives no figure)
Driver
T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Holosun 407C X2 on the Heckler & Koch VP9 Optics Ready, Optic to plate: thread not on file; torque per the optic maker (HK's manual gives no figure); driver T10 / T15. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407c-x2-on-heckler-and-koch-vp9-optics-ready/#joint-optic-plate

Published for this exact pairing
  • Night Fision · absolute · front .480 / rear .517 in
  • Night Fision · lower 1/3 · front .350 / rear .387 in
Heights are front / rear in inches, as each sight maker measures its own sights. That's not a deck height, and it doesn't compare across makers to the thousandth. Absolute puts the front sight level with the dot; lower 1/3 and lower 1/5 sit it lower in the window. A sight maker sells a handful of fixed heights, so optics of similar height share one set: the same figures under two optics are the maker's chart saying so, not a copy.Night Fision — co-witness chart for HK (not split by model) ↗
With the sights already on itStandard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. The published heights are for aftermarket sight sets, not factory irons, so "no co-witness" is the typical case rather than a guarantee: some optics still show factory-height irons in the lower third or lower fifth of the window.Taller sights made for this optic are the published ones above.
On this modelHK's manual lists the Optic Ready plates as not included with the pistol: it comes with a cover plate over the cut, and the plate is bought separately.
How this slide mounts an opticHK sells the Optic Ready plates separately: its manual lists them as "not included with VP Optic Ready", and HK USA's VP9 Match page says the cut takes "one of five available mounting plates (sold separately)". The slide ships with a cover plate over the cut. HK's plates are numbered: its manual lists plate 01 (Meopta MeoSight III, EOTech MRDS, Noblex Sight III), 02 (Trijicon RMR, Holosun), 03 (C-More STS2), 04 (Leupold DeltaPoint) and 05 (Burris FastFire 2 and 3, Vortex Viper and Venom); HK USA's webshop adds an ACRO plate (6), a Holosun K plate that also lists the Shield RMSc, and a 509T plate. HK names optics one by one, so each of its plates is listed here for the optics it names, not for the whole footprint. C&H and EGW sell plates for more. Source: Heckler & Koch USA, VP9A1 operator's manual (plates 1 to 7 and the Holosun K and 509T plates, 2 Nm, optic screws to the optic maker's torque) ↗; Heckler & Koch USA, VP9 Match ↗; Heckler & Koch USA webshop, Optics Plate #2 for VP9 Optic Ready Models ↗.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height and the HK Optics Plate #2 (50254262). Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Heckler & Koch VP9 Optics Ready
Optic
Holosun 407C X2
Footprint
Trijicon RMR
Slide
HK VP9 / SFP9 OR plate system
Mount
Adapter plate required

Parts to order

1 ×Holosun 407C X2Trijicon RMR footprint · 2 MOA$150–300
1 ×HK Optics Plate #2 (50254262)HK factory — HK says "Trijicon RMR and Holosun", and not the Holosun 507K or the Trijicon RMRcc. It does not name the SRO or any other maker's RMR-pattern optic, so they are not listed here; C&H's plate names the SRO.$25–60
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$175–360

Where to buy

Holosun 407C X2Trijicon RMR footprintHolosun — this item ↗
HK Optics Plate #2 (50254262)HK factoryHK factory — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideM4The two screws that hold the cover plate on the slide, reused for the plate (HK sells spares, part 50947116, and says to replace them after 2,000 rounds).
HK's own instruction is to mount the optic plate with the two screws that hold the cover plate on the Optic Ready slide, so unlike most slides these are the same screws: take the cover plate off, fit the plate with them, and keep the cover plate for when the optic comes off. HK says to use thread locker on these screws, and to replace them with new ones after 2,000 rounds.
Optic → plateper plate maker, not on file hereNot stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying.
Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy.

On the bench before you start

  • Torque wrench — covering 17.7 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10 / T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slide2 Nm (17.7 in-lb, converted)
Optic torqueper the optic maker (HK's manual gives no figure)
Screwsper plate maker, not on file here
DriverT10 / T15
Interface2 screws, 2 forward recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Optic → plate thread
Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (7)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Holosun 407C X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Heckler & Koch VP9 Optics Ready’s slide: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The HK Optics Plate #2 (50254262): The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026. The VP9 / SFP9 → Trijicon RMR / SRO / Holosun C: The HK VP9 / SFP9 OR plate system: HK USA's VP Series operator's manual (2025) and VP9A1 manual (2026), HK USA's webshop plate listings (parts 50254261 to 50254265, 50257961, 51000381, 51000792, 50947116, 51000950, 51000951), HK USA's VP9 Match page, Heckler & Koch GmbH's SFP9 page and publication, and C&H's and EGW's listings for the VP9 OR checked against Heckler & Koch USA (hk-usa.com, us.hkwebshop.com), Heckler & Koch GmbH (heckler-koch.com), C&H Precision (chpws.com) and EGW (egwguns.com), read 2026-10-01 on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.