Home / Pistols / Springfield Armory Echelon / Trijicon RMR Type 2

Does the Trijicon RMR Type 2 fit the Springfield Armory Echelon?

Yes, the Trijicon RMR Type 2 mounts straight to the Springfield Armory Echelon with no adapter plate; the optic is the only part to buy.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Direct mount

The slide is cut for this footprint, so the optic bolts straight on.

What to buy

Optic
Trijicon RMR Type 2 ($450–650)
Plate
None: it mounts straight to the slide.
Screws
#6-32, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
All in
$450–650 approximate street prices, September 2026
Same answer forThe Trijicon RMR Type 2 goes on the Springfield Armory Echelon 4.0C and Springfield Armory Echelon Compact 4.5C the same way: they share this slide's optic cut.
SlideSpringfield Echelon VIS
Optic footprintTrijicon RMR
Optic screws#6-32 · T10 / T15
Optic torque15 in-lb
Cost to mount$450–650

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Pins → slide

Pin set
1From Springfield Armory, Echelon VIS fitment chart (2023-08-03) ↗, checked against it October 1, 2026 (the pin set and screw source for each optic, and the plate hardware).
Thread
No thread — interference fit

Cite this joint The Trijicon RMR Type 2 on the Springfield Armory Echelon, Pins to slide: pin set 1; thread No thread — interference fit. Source: Springfield Armory, Echelon VIS fitment chart (2023-08-03) (https://www.springfield-armory.com/wp-content/uploads/vis-fitment-chart-2023-08-03.pdf), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-springfield-armory-echelon/#joint-pins-slide

Optic → slide

Thread
#6-32The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Torque
15 in-lbThe footprint's usual figure, but no document is linked for it here yet. What would settle it.
Driver
T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Trijicon RMR Type 2 on the Springfield Armory Echelon, Optic to slide: thread #6-32; torque 15 in-lb; driver T10 / T15. No maker document on file for the thread or torque or driver. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-springfield-armory-echelon/#joint-optic-slide

Published for this exact pairing
  • Springfield Armory · co-witness · front .250 / rear .270 in
Heights are front / rear in inches, as each sight maker measures its own sights. That's not a deck height, and it doesn't compare across makers to the thousandth. Absolute puts the front sight level with the dot; lower 1/3 and lower 1/5 sit it lower in the window. A sight maker sells a handful of fixed heights, so optics of similar height share one set: the same figures under two optics are the maker's chart saying so, not a copy.Springfield Armory — Echelon U-Dot sight set, sold in optic-specific heights ↗
With the sights already on itStandard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. The published heights are for aftermarket sight sets, not factory irons, so "no co-witness" is the typical case rather than a guarantee: some optics still show factory-height irons in the lower third or lower fifth of the window.Taller sights made for this optic are the published ones above.
How this slide mounts an opticInstead of plates, self-locking pins drop into the slide to recreate a footprint's lugs. Springfield's VIS chart gives pin set 1 to RMR-pattern optics (and the Holosun 507K and EPS), set 2 to DeltaPoint Pro and set 3 to Shield, with its own screw kit for the RMR family and DeltaPoint Pro. The optic bolts straight to the slide, so nothing stacks. ACRO and Docter optics need one of Springfield's adapter plates.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Springfield Armory Echelon
Optic
Trijicon RMR Type 2
Footprint
Trijicon RMR
Slide
Springfield Echelon VIS
Mount
Direct mount

Parts to order

1 ×Trijicon RMR Type 2Trijicon RMR footprint · 1.0 / 3.25 / 6.5 MOA$450–650
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic only$450–650

Where to buy

Trijicon RMR Type 2Trijicon RMR footprintTrijicon — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Pins → slideNo thread — interference fitPin set 1, per Springfield's VIS fitment chart.
Springfield sells the three pin sets together as the Echelon Complete Pin Set, so check which your pistol came with. The pins locate the optic; the screws hold it.
Optic → slide#6-32Springfield's Echelon screw kit 1A, sold separately: Springfield's chart does not use the optic's own.
The optic bolts straight to the slide with nothing underneath. Springfield's chart gives this optic its own screw kit rather than the screws in the box.

On the bench before you start

  • Torque wrench — covering 15 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10 / T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • Tweezers — the VIS locating pins are small and directional
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Optic torque15 in-lb
Screws#6-32
DriverT10 / T15
Interface2 screws, 2 forward recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the cover plate and confirm which pin set the optic's footprint needs.
  3. Fit the pins: front pins flat side down, rear pins larger diameter up. Tweezers help.
  4. Degrease the slide cut and the optic base.
  5. Seat the optic over the pins and fit its screws with blue threadlocker, then torque to the optic spec.
  6. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  7. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (6)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Trijicon RMR Type 2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Springfield Armory Echelon’s slide: the pin set and screw source for each optic, and the plate hardware checked against Springfield's Echelon VIS fitment chart, plate instructions and store listings on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.