Does the Trijicon RMR Type 2 fit the Staccato P?
Yes, the Trijicon RMR Type 2 fits the Staccato P with an adapter plate: the Staccato → Trijicon RMR / RMR HD / SRO from Dawson Precision.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
The slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.
- Staccato → Trijicon RMR / RMR HD / SRODawson Precision ↗$60–95Dawson's DPO-ECO tactical plate, one piece with a non-adjustable rear sight; Staccato sells it as a mounting kit with screws. It takes the tactical-height front sight.
What to buy
- Optic
- Trijicon RMR Type 2 ($450–650)
- Plate
- The Staccato → Trijicon RMR / RMR HD / SRO, from Dawson Precision ($60–95).
- Screws
- Use the ones that come with the plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
- All in
- $510–745 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- 25 in-lbFrom Staccato, Dawson DPO Trijicon RMR / RMRHD / SRO Eco mounting kit (torque specification 25 in-lbs) ↗, checked against it October 1, 2026 (The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01).).
Cite this joint The Trijicon RMR Type 2 on the Staccato P, Plate to slide: thread not on file; torque 25 in-lb. Source: Staccato, Dawson DPO Trijicon RMR / RMRHD / SRO Eco mounting kit (torque specification 25 in-lbs) (https://staccato2011.com/products/dawson-precision-patented-dpo-trijicon-rmr-rmrhd-sro-eco-mounting-kit), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-staccato-p/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- 25 in-lbFrom Staccato, Dawson DPO Trijicon RMR / RMRHD / SRO Eco mounting kit (torque specification 25 in-lbs) ↗, checked against it October 1, 2026 (The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01).).
- Driver
- T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Trijicon RMR Type 2 on the Staccato P, Optic to plate: thread not on file; torque 25 in-lb; driver T10 / T15. Source: Staccato, Dawson DPO Trijicon RMR / RMRHD / SRO Eco mounting kit (torque specification 25 in-lbs) (https://staccato2011.com/products/dawson-precision-patented-dpo-trijicon-rmr-rmrhd-sro-eco-mounting-kit), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/trijicon-rmr-type-2-on-staccato-p/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Staccato P
- Optic
- Trijicon RMR Type 2
- Footprint
- Trijicon RMR
- Slide
- Staccato / 2011 optic plate system
- Mount
- Adapter plate required
Parts to order
| 1 × | Trijicon RMR Type 2Trijicon RMR footprint · 1.0 / 3.25 / 6.5 MOA | $450–650 |
| 1 × | Staccato → Trijicon RMR / RMR HD / SRODawson Precision — Dawson's DPO-ECO tactical plate, one piece with a non-adjustable rear sight; Staccato sells it as a mounting kit with screws. It takes the tactical-height front sight. | $60–95 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $510–745 |
Where to buy
| Trijicon RMR Type 2Trijicon RMR footprint | Trijicon — this item ↗ |
| Staccato → Trijicon RMR / RMR HD / SRODawson Precision | Dawson Precision — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | per plate maker, not on file here | Supplied with the plate. If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths. |
| Optic → plate | per plate maker, not on file here | Supplied with the plate, not the optic. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — covering 25 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Plate → slide thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Staccato P with other optics
Plate11
Every optic on the Staccato P, and how each mounts
The Trijicon RMR Type 2 on other pistols
Direct4
Plate in box8
Plate11
By serial1
Sources for this page (8)
- Slide Staccato, optic mounting kits (seven Dawson Precision DPO kits for the V2 / V3 line, and a separate HD HOST kit) ↗
- Slide Staccato, knowledge center FAQs (optic-ready, other makers' plates, optics not listed) ↗
- Slide Staccato, Staccato P product page (free optic mounting with an optic and its plate) ↗
- Slide Staccato, Staccato XC product page ("optic-specific Staccato mounting plates are included") ↗
- Slide Staccato, Dawson Precision optic system slide milling service (C, C2 and P) ↗
- Optic Trijicon, RMR spec sheet (PML4014-2) ↗
- Plate Dawson Precision, Staccato → Trijicon RMR / RMR HD / SRO ↗
- Plate Staccato, Dawson DPO Trijicon RMR / RMRHD / SRO Eco mounting kit (torque specification 25 in-lbs) ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Trijicon RMR Type 2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Staccato P’s slide: The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01). checked against Staccato's own store and knowledge center (staccato2011.com) and Dawson Precision's own listings (dawsonprecision.com) on October 1, 2026. The Staccato → Trijicon RMR / RMR HD / SRO: The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01). checked against Staccato's own store and knowledge center (staccato2011.com) and Dawson Precision's own listings (dawsonprecision.com) on October 1, 2026.