Home / Pistols / Staccato P / Aimpoint ACRO P-2

Does the Aimpoint ACRO P-2 fit the Staccato P?

Yes, the Aimpoint ACRO P-2 fits the Staccato P with an adapter plate: the Staccato → Aimpoint ACRO P-1 / P-2 from Dawson Precision.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

Enclosed emitter

The slide isn't cut for this pattern. One plate adapts it, listed below. The plate gives the optic's clamp a rail to grip.

  • Staccato → Aimpoint ACRO P-1 / P-2Dawson Precision ↗$60–95Dawson's DPO-ECO tactical plate for the ACRO P-1 and P-2; the optic clamps to the plate. Dawson does not name the ACRO C-2.

What to buy

Optic
Aimpoint ACRO P-2 ($650+)
Plate
The Staccato → Aimpoint ACRO P-1 / P-2, from Dawson Precision ($60–95).
Screws
Cross-bolt clamp, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: low at best (estimated, why).
All in
$710–995 approximate street prices, September 2026
Same answer forThe Aimpoint ACRO P-2 goes on the Staccato C2, Staccato XC and Staccato XL the same way: they share this slide's optic cut.
SlideStaccato / 2011 optic plate system
Optic footprintAimpoint ACRO
Optic screwsCross-bolt clamp · T10 / hex per model
Optic torqueper Aimpoint manual
Plate to slide25 in-lb
Cost to mount$710–995

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
set by the slide
Torque
25 in-lbFrom Staccato, Dawson DPO Aimpoint ACRO Eco mounting kit (torque specification 25 in-lbs) ↗, checked against it October 1, 2026 (The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01).).

Cite this joint The Aimpoint ACRO P-2 on the Staccato P, Plate to slide: thread set by the slide; torque 25 in-lb. Source: Staccato, Dawson DPO Aimpoint ACRO Eco mounting kit (torque specification 25 in-lbs) (https://staccato2011.com/products/dawson-precision-patented-dpo-aimpoint-acro-eco-mounting-kit), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/aimpoint-acro-p-2-on-staccato-p/#joint-plate-slide

Optic → interface

Thread
Cross-bolt clamp
Torque
per Aimpoint manual
Driver
T10 / hex per modelThe footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Aimpoint ACRO P-2 on the Staccato P, Optic to interface: thread Cross-bolt clamp; torque per Aimpoint manual; driver T10 / hex per model. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/aimpoint-acro-p-2-on-staccato-p/#joint-optic-interface

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Low at best. An enclosed emitter on a plate sits tall, so suppressor-height irons land at the very bottom of the window or below it: Night Fision lists its .290 in front sight as a lower 1/5 co-witness for an ACRO P-2 on GLOCK's MOS plate, and taller optics lose them. Sights taller than suppressor height are the usual fix. This optic's window runs small (15 × 15 mm), so a front sight slightly off the ideal height is more likely to miss it. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
On this modelStaccato's ROMEOZero / JPoint / Shield kit is listed for the CS and C2, not the P; Dawson lists its carry plates for DPO pistols with a carry-height front sight. Ask Staccato before buying a carry plate.
How this slide mounts an opticOptic-ready Staccato slides take Dawson Precision's DPO plates, one for each optic: the plate replaces the slide's cover plate and carries the rear sight, so it also sets the iron-sight height. Staccato says the system is proprietary (other makers' plates do not fit), names the optics it supports, and will not modify a plate for one it does not name, so each plate below is limited to the optics its maker lists. Staccato's kit listings give 25 in-lb for the kit and do not say whether that is the plate screws or the optic screws; neither maker gives a thread, so the thread is not on file. Staccato's kits are for its V2 and V3 pistols, not the HD series. Its XC and XL pages say optic-specific mounting plates are included with the Tactical Optic system but not whether one comes in the pistol's box, so no plate is counted as in the box. Source: Staccato, Staccato P product page (free optic mounting with an optic and its plate) ↗; Staccato, Staccato XC product page ("optic-specific Staccato mounting plates are included") ↗; Staccato, Dawson Precision optic system slide milling service (C, C2 and P) ↗.
About this optic50,000-hour runtime on one cell. Small window, sealed housing.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Staccato P
Optic
Aimpoint ACRO P-2
Footprint
Aimpoint ACRO
Slide
Staccato / 2011 optic plate system
Mount
Adapter plate required

Parts to order

1 ×Aimpoint ACRO P-2Aimpoint ACRO footprint · 3.5 MOA$650+
1 ×Staccato → Aimpoint ACRO P-1 / P-2Dawson Precision — Dawson's DPO-ECO tactical plate for the ACRO P-1 and P-2; the optic clamps to the plate. Dawson does not name the ACRO C-2.$60–95
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$710–995

Where to buy

Aimpoint ACRO P-2Aimpoint ACRO footprintAimpoint — this item ↗
Staccato → Aimpoint ACRO P-1 / P-2Dawson PrecisionDawson Precision — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideset by the slideSupplied with the plate.
The one screwed joint in this stack, so it gets the threadlocker and the torque check. Keep the pistol's cover-plate screws apart from these.
Optic → interfaceCross-bolt clampSupplied with the optic.
The ACRO clamps rather than bolting through, so there's no screw length to get wrong. Torque the cross-bolt to Aimpoint's figure.

On the bench before you start

  • Torque wrench — covering 25 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10 / hex per model, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slide25 in-lb
Optic torqueper Aimpoint manual
ScrewsCross-bolt clamp
DriverT10 / hex per model
InterfaceClamp interface with recoil shoulder — not a screw-and-lug pattern

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Set the optic on the plate's rail and tighten its cross-bolt clamp to Aimpoint's figure. There are no optic screws to fit.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (7)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Staccato P’s slide: The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01). checked against Staccato's own store and knowledge center (staccato2011.com) and Dawson Precision's own listings (dawsonprecision.com) on October 1, 2026. The Staccato → Aimpoint ACRO P-1 / P-2: The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01). checked against Staccato's own store and knowledge center (staccato2011.com) and Dawson Precision's own listings (dawsonprecision.com) on October 1, 2026. Not individually re-checked since it was compiled (September 2026): the optic’s figures.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.