Home / Pistols / Staccato P / Holosun 509T

Does the Holosun 509T fit the Staccato P?

Yes, the Holosun 509T fits the Staccato P with an adapter plate: the Staccato → Holosun 509T from Dawson Precision.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

Enclosed emitter

The slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.

  • Staccato → Holosun 509TDawson Precision ↗$60–95Dawson's DPO-ECO tactical plate; it does not fit the 509T ACSS Vulcan.

What to buy

Optic
Holosun 509T ($450–650)
Plate
The Staccato → Holosun 509T, from Dawson Precision ($60–95).
Screws
Use the ones that come with the plate.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: low at best (estimated, why).
All in
$510–745 approximate street prices, September 2026
Same answer forThe Holosun 509T goes on the Staccato C2, Staccato XC and Staccato XL the same way: they share this slide's optic cut.
SlideStaccato / 2011 optic plate system
Optic footprintHolosun 509T
Optic screwsper plate maker, not on file here · T10
Optic torque25 in-lb
Plate to slide25 in-lb
Cost to mount$510–745

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
per plate maker, not on file hereNot on file. What would settle it.
Torque
25 in-lbFrom Staccato, Dawson DPO Holosun 509T Eco mounting kit (torque specification 25 in-lbs) ↗, checked against it October 1, 2026 (The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01).).

Cite this joint The Holosun 509T on the Staccato P, Plate to slide: thread not on file; torque 25 in-lb. Source: Staccato, Dawson DPO Holosun 509T Eco mounting kit (torque specification 25 in-lbs) (https://staccato2011.com/products/dawson-precision-patented-dpo-holosun-509t-eco-mounting-kit), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/holosun-509t-on-staccato-p/#joint-plate-slide

Optic → plate

Thread
per plate maker, not on file hereNot on file. What would settle it.
Torque
25 in-lbFrom Staccato, Dawson DPO Holosun 509T Eco mounting kit (torque specification 25 in-lbs) ↗, checked against it October 1, 2026 (The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01).).
Driver
T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Holosun 509T on the Staccato P, Optic to plate: thread not on file; torque 25 in-lb; driver T10. Source: Staccato, Dawson DPO Holosun 509T Eco mounting kit (torque specification 25 in-lbs) (https://staccato2011.com/products/dawson-precision-patented-dpo-holosun-509t-eco-mounting-kit), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-509t-on-staccato-p/#joint-optic-plate

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Low at best. An enclosed emitter on a plate sits tall, so suppressor-height irons land at the very bottom of the window or below it: Night Fision lists its .290 in front sight as a lower 1/5 co-witness for an ACRO P-2 on GLOCK's MOS plate, and taller optics lose them. Sights taller than suppressor height are the usual fix. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
On this modelStaccato's ROMEOZero / JPoint / Shield kit is listed for the CS and C2, not the P; Dawson lists its carry plates for DPO pistols with a carry-height front sight. Ask Staccato before buying a carry plate.
How this slide mounts an opticOptic-ready Staccato slides take Dawson Precision's DPO plates, one for each optic: the plate replaces the slide's cover plate and carries the rear sight, so it also sets the iron-sight height. Staccato says the system is proprietary (other makers' plates do not fit), names the optics it supports, and will not modify a plate for one it does not name, so each plate below is limited to the optics its maker lists. Staccato's kit listings give 25 in-lb for the kit and do not say whether that is the plate screws or the optic screws; neither maker gives a thread, so the thread is not on file. Staccato's kits are for its V2 and V3 pistols, not the HD series. Its XC and XL pages say optic-specific mounting plates are included with the Tactical Optic system but not whether one comes in the pistol's box, so no plate is counted as in the box. Source: Staccato, Staccato P product page (free optic mounting with an optic and its plate) ↗; Staccato, Staccato XC product page ("optic-specific Staccato mounting plates are included") ↗; Staccato, Dawson Precision optic system slide milling service (C, C2 and P) ↗.
About this opticTitanium; duty-oriented. Steel plates recommended.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Staccato P
Optic
Holosun 509T
Footprint
Holosun 509T
Slide
Staccato / 2011 optic plate system
Mount
Adapter plate required

Parts to order

1 ×Holosun 509THolosun 509T footprint · 2 MOA + 32 MOA circle$450–650
1 ×Staccato → Holosun 509TDawson Precision — Dawson's DPO-ECO tactical plate; it does not fit the 509T ACSS Vulcan.$60–95
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$510–745

Where to buy

Holosun 509THolosun 509T footprintHolosun ↗
Staccato → Holosun 509TDawson PrecisionDawson Precision — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideper plate maker, not on file hereSupplied with the plate.
If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths.
Optic → plateper plate maker, not on file hereSupplied with the plate, not the optic.
Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy.

On the bench before you start

  • Torque wrench — covering 25 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slide25 in-lb
Optic torque25 in-lb
Screwsper plate maker, not on file here
DriverT10
InterfaceProprietary screw and lug pattern

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Plate → slide thread
Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
Optic → plate thread
Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (8)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Holosun 509T: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Staccato P’s slide: The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01). checked against Staccato's own store and knowledge center (staccato2011.com) and Dawson Precision's own listings (dawsonprecision.com) on October 1, 2026. The Staccato → Holosun 509T: The Staccato DPO plate system: Staccato's optic mounting kit category and the seven DPO kit pages, its knowledge-center FAQs (optic chart, torque chart, optic-ready, other makers' plates), the C2, P, XC and XL product pages, the optic mounting and slide milling service pages, and Dawson Precision's eleven Staccato DPO plate listings (2026-10-01). checked against Staccato's own store and knowledge center (staccato2011.com) and Dawson Precision's own listings (dawsonprecision.com) on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.