Does the Holosun 509T fit the Canik METE SFx?
Yes, the Holosun 509T fits the Canik METE SFx with an adapter plate: the METE 509T DOGTAG from Calculated Kinetics.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
Enclosed emitterThe slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.
- METE 509T DOGTAGCalculated Kinetics ↗$60–95Shown sold out on Calculated Kinetics' page when read (2026-10-01).
What to buy
- Optic
- Holosun 509T ($450–650)
- Plate
- The METE 509T DOGTAG, from Calculated Kinetics ($60–95).
- Screws
- Use the ones that come with the plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: low at best (estimated, why).
- All in
- $510–745 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate maker, not on file hereNot on file. What would settle it.
Cite this joint The Holosun 509T on the Canik METE SFx, Plate to slide: thread not on file; torque not on file. Optic Mounting, https://opticmounting.com/fit/holosun-509t-on-canik-mete-sfx/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate maker, not on file here (15 in-lb plate / 20 in-lb optic is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Holosun 509T on the Canik METE SFx, Optic to plate: thread not on file; torque not on file; driver T10. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-509t-on-canik-mete-sfx/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Canik METE SFx
- Optic
- Holosun 509T
- Footprint
- Holosun 509T
- Slide
- Canik METE optic cut (RMSc plus RMRcc or RMR)
- Mount
- Adapter plate required
Parts to order
| 1 × | Holosun 509THolosun 509T footprint · 2 MOA + 32 MOA circle | $450–650 |
| 1 × | METE 509T DOGTAGCalculated Kinetics — Shown sold out on Calculated Kinetics' page when read (2026-10-01). | $60–95 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $510–745 |
Where to buy
| Holosun 509THolosun 509T footprint | Holosun ↗ |
| METE 509T DOGTAGCalculated Kinetics | Calculated Kinetics — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | per plate maker, not on file here | Supplied with the plate. If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths. |
| Optic → plate | per plate maker, not on file here | Supplied with the plate, not the optic. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T10, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Plate → slide thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Plate-to-slide torque
- Not published for this plate. Use the plate maker's figure.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Canik METE SFx with other optics
Plate in box2
No fit1
Every optic on the Canik METE SFx, and how each mounts
The Holosun 509T on other pistols
Plate17
- GLOCK 19 Gen5 MOS
- Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)
- SIG Sauer P320 X-Carry
- GLOCK 17 Gen5 MOS
- Walther PDP Full Size (1.0)
- Shadow Systems MR920
- GLOCK 45 Gen5 MOS
- GLOCK 26 Gen5 MOS
- SIG Sauer P320 XCompact
- Smith & Wesson M&P9 M2.0 Compact Optics Ready
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Walther PDP Compact (1.0)
- CZ P-10 C Optics Ready
- Heckler & Koch VP9 Optics Ready
- Staccato P
- CZ Shadow 2 Optics Ready
- Canik TTI Combat
No fit13
- SIG Sauer P365XL
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- GLOCK 48 MOS
- Springfield Armory Echelon
- Ruger RXM
- SIG Sauer P365X
- SIG Sauer P365 Optics Ready
- SIG Sauer P365-XMACRO / XMACRO Comp
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Taurus GX4 TORO / GX4XL
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
Sources for this page (10)
- Slide Canik, METE SFT owner's manual (2026), Optic Sight Interfaces ↗
- Slide Canik, METE SFx owner's manual (2026), Optic Sight Interfaces ↗
- Slide Canik, METE SF owner's manual (2025), Optic Sight Interfaces ↗
- Slide Canik, METE SFT Pro owner's manual (2025), Optic Sight Interfaces ↗
- Slide Canik, METE SFT product page (serial numbers by optic footprint) ↗
- Slide Canik, METE SFx product page ↗
- Slide Canik, METE SF product page ↗
- Slide Canik, METE SFT Pro product page ↗
- Optic Holosun, HE509T-X2 (the current 509T) ↗
- Plate Calculated Kinetics, METE 509T DOGTAG ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Holosun 509T: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Canik METE SFx’s slide: optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link checked against Canik's owner's manuals (METE SFT, SFx, SF and SFT Pro; TP9 SFx; SFx Rival and Rival-S; TTI Combat; TP9 Elite SC), its product and parts pages on canik.com, and Calculated Kinetics' own listings on October 1, 2026. The METE 509T DOGTAG: optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link checked against Canik's owner's manuals (METE SFT, SFx, SF and SFT Pro; TP9 SFx; SFx Rival and Rival-S; TTI Combat; TP9 Elite SC), its product and parts pages on canik.com, and Calculated Kinetics' own listings on October 1, 2026.