Does the Shield Sights RMSc fit the Canik METE SFx?
Yes, the Shield Sights RMSc fits the Canik METE SFx on a plate that ships with the pistol (Canik interface 01 or 02 → RMSc); the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Fits on the plate in the box
The Canik interface 01 or 02 → RMSc that ships with the pistol adapts the slide to this footprint.
- Canik interface 01 or 02 → RMScCanik factory ↗in the boxCanik's manual packs M4 screws with the pistol for interfaces 1 and 2, and says to use only those to install the interface bases. Interface 1 is the one Canik lists for the Shield RMS and SMS family, JPoint and AMS; 2 for the RMSc and SMSc. Canik gives no thread or torque for the optic's own screws.Plate screws M4 · optic screws not in Canik factory's listing · from Canik, METE SFT owner's manual (2026), Optic Sight Interfaces ↗
What to buy
- Optic
- Shield Sights RMSc ($150–300)
- Plate
- None to buy: the Canik interface 01 or 02 → RMSc ships with the pistol. Look in the box.
- Screws
- Look in the pistol's box with the plates; if there are none, buy a pair made for this plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
- All in
- $150–300 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M4From Canik, METE SFT owner's manual (2026), Optic Sight Interfaces ↗, checked against it October 1, 2026 (optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link).
- Torque
- per plate maker, not on file hereNot on file. What would settle it.
Cite this joint The Shield Sights RMSc on the Canik METE SFx, Plate to slide: thread M4; torque not on file. Source: Canik, METE SFT owner's manual (2026), Optic Sight Interfaces (https://cdn.shopify.com/s/files/1/0829/2528/9506/files/METE_SFT_Manual.pdf), checked 2026-10-01. Optic Mounting, https://opticmounting.com/fit/shield-sights-rmsc-on-canik-mete-sfx/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate maker, not on file here (10–15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Shield Sights RMSc on the Canik METE SFx, Optic to plate: thread not on file; torque not on file; driver T10 / T15. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/shield-sights-rmsc-on-canik-mete-sfx/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Canik METE SFx
- Optic
- Shield Sights RMSc
- Footprint
- Shield RMSc
- Slide
- Canik METE optic cut (RMSc plus RMRcc or RMR)
- Mount
- Fits on the plate in the box
Parts to order
| 1 × | Shield Sights RMScShield RMSc footprint · 4 / 8 MOA | $150–300 |
| have | Canik interface 01 or 02 → RMScCanik factory — Canik's manual packs M4 screws with the pistol for interfaces 1 and 2, and says to use only those to install the interface bases. Interface 1 is the one Canik lists for the Shield RMS and SMS family, JPoint and AMS; 2 for the RMSc and SMSc. Canik gives no thread or torque for the optic's own screws. | in the box |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only (plate ships with the pistol) | $150–300 |
Where to buy
| Shield Sights RMScShield RMSc footprint | |
| Canik interface 01 or 02 → RMSc | Ships with the pistol |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M4 | Supplied with the plate. Two kinds of short screw come with the pistol: these, for the plate, and the pair already holding the cover plate on the slide. They are different lengths, so keep them apart. |
| Optic → plate | per plate maker, not on file here | Look in the pistol's box, with the plates. If there are none, buy a pair made for this plate. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Plate-to-slide torque
- Not published for this plate. Use the plate maker's figure.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Canik METE SFx with other optics
Plate in box1
No fit1
Every optic on the Canik METE SFx, and how each mounts
The Shield Sights RMSc on other pistols
Direct10
Direct (cross-fit)3
Plate in box3
Plate12
Sources for this page (9)
- Slide Canik, METE SFT owner's manual (2026), Optic Sight Interfaces ↗
- Slide Canik, METE SFx owner's manual (2026), Optic Sight Interfaces ↗
- Slide Canik, METE SF owner's manual (2025), Optic Sight Interfaces ↗
- Slide Canik, METE SFT Pro owner's manual (2025), Optic Sight Interfaces ↗
- Slide Canik, METE SFT product page (serial numbers by optic footprint) ↗
- Slide Canik, METE SFx product page ↗
- Slide Canik, METE SF product page ↗
- Slide Canik, METE SFT Pro product page ↗
- Optic Shield Sights, RMSc ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Shield Sights RMSc: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Canik METE SFx’s slide: optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link checked against Canik's owner's manuals (METE SFT, SFx, SF and SFT Pro; TP9 SFx; SFx Rival and Rival-S; TTI Combat; TP9 Elite SC), its product and parts pages on canik.com, and Calculated Kinetics' own listings on October 1, 2026. The Canik interface 01 or 02 → RMSc: optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link checked against Canik's owner's manuals (METE SFT, SFx, SF and SFT Pro; TP9 SFx; SFx Rival and Rival-S; TTI Combat; TP9 Elite SC), its product and parts pages on canik.com, and Calculated Kinetics' own listings on October 1, 2026.