Does the Shield Sights RMSc fit the Springfield Armory Hellcat Pro?
Yes. It mounts straight to the slide with no adapter plate; the optic is the only part to buy.
Direct mount
The slide is cut for this footprint, so the optic bolts straight on.
Same answer forThe Shield Sights RMSc goes on the Springfield Armory Hellcat OSP the same way: it shares this slide's optic cut.
SlideSpringfield Hellcat OSP cut (Micro footprint)
Optic footprintShield RMSc
Optic screwsM4 × 0.7 · T10 / T15
Optic torque10–15 in-lb, per the optic or plate maker
Cost to mount$150–300
New to red dots? What footprint, plate, co-witness and the rest mean →
Slide threadTapped M4 × 0.7. Source: Springfield Armory, Hellcat manual ↗; SIG Sauer, ROMEO-X M3 & M4 screw kit ↗.
Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't.With suppressor-height irons: Co-witnesses. A ≈0.290–0.315 in front sight normally sits in the lower third of the window on a direct cut. Mounted directly, the optic sits as low as the cut allows, the best case for a co-witness. That's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
How this slide mounts an opticMilled for what Springfield calls its Micro footprint, the Shield RMSc pattern: an RMSc-pattern optic, Springfield's own Hex Wasp included, bolts straight on. A Holosun K optic takes a plate: C&H says its plate is what lets a 407K or 507K go on without modifying the slide's recoil posts. Source: C&H Precision, Hellcat to Holosun 407K / 507K ↗.
About this opticThe lightest and lowest of the common slim optics. The battery sits under the optic, so every change means taking it off the slide and re-zeroing (Shield's own instructions).
GuidesShield RMSc vs Holosun K: which optic fits which cut · Suppressor-height sights: will your irons co-witness? · Red dot lost zero? Troubleshooting the mount
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Rather not do it yourself? Mounting an optic is a short bench job for most gun shops and gunsmiths. Buy the parts under "Parts to order" and take this sheet with you.
Build sheet
Data compiled September 2026 · Optic Mounting
- Pistol
- Springfield Armory Hellcat Pro
- Optic
- Shield Sights RMSc
- Footprint
- Shield RMSc
- Slide
- Springfield Hellcat OSP cut (Micro footprint)
- Mount
- Direct mount
Parts to order
| 1 × | Shield Sights RMScShield RMSc footprint · 4 / 8 MOA | $150–300 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only | $150–300 |
Where to buy
| Shield Sights RMScShield RMSc footprint | |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Optic → slide | M4 × 0.7 | Supplied with the optic. With no plate in the stack, the screws that came with the optic are normally correct. The pistol's cover-plate screws are not optic screws; set them aside. |
On the bench before you start
- Torque wrench — covering 15 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Optic torque10–15 in-lb, per the optic or plate maker
ScrewsM4 × 0.7
DriverT10 / T15
Interface2 screws, 4 recoil lugs (2 front, 2 rear)
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the cover plate and set it aside with its screws.
- Degrease the slide cut and the optic base.
- Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
- Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.
Sight co-witness
Answered above: co-witness with standard and suppressor-height irons.
Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
The Springfield Armory Hellcat Pro with other optics
- Holosun 507C X2 Plate
- Trijicon RMR Type 2 Plate
- Holosun 507K X2 Plate
- Holosun EPS Carry Plate
- Aimpoint ACRO P-2 No fit
- Trijicon SRO Plate
- Leupold DeltaPoint Pro No fit
- Vortex Defender-CCW Direct
- Holosun 407C X2 Plate
- Steiner MPS No fit
- Holosun 509T No fit
- Trijicon RMRcc No fit
- Holosun 407K X2 Plate
Every optic on the Springfield Armory Hellcat Pro, and how each mounts →
The Shield Sights RMSc on other pistols
- GLOCK 19 Gen5 MOS Plate
- SIG Sauer P365XL Direct
- GLOCK 43X MOS Direct
- Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in) Plate in box
- Springfield Armory Hellcat OSP Direct
- SIG Sauer P320 X-Carry Plate
- GLOCK 17 Gen5 MOS Plate
- GLOCK 48 MOS Direct
- Springfield Armory Echelon Direct (cross-fit)
- Walther PDP Full Size (1.0) Plate
- Shadow Systems MR920 Plate
- Ruger RXM Plate
- GLOCK 45 Gen5 MOS Plate
- GLOCK 26 Gen5 MOS Plate
- SIG Sauer P365X Direct
- SIG Sauer P365 Optics Ready Direct
- SIG Sauer P365-XMACRO / XMACRO Comp Direct
- Smith & Wesson M&P Shield Plus Optics Ready Direct
- Canik METE SFx Direct
- SIG Sauer P320 XCompact Plate
- Smith & Wesson M&P9 M2.0 Compact Optics Ready Plate in box
- GLOCK 17 / 19 / 45 Gen6 (ORS) No fit
- Walther PDP Compact (1.0) Plate
- CZ P-10 C Optics Ready Plate
- Heckler & Koch VP9 Optics Ready Plate
- Taurus GX4 TORO / GX4XL Direct
- Palmetto State Armory Dagger Full Size / Compact (RMR cut) No fit
Something on this page wrong?
Tell us what it should be, and include a source: nothing changes without one.