Does the Holosun 407K X2 fit the Springfield Armory Hellcat Pro?
Yes, the Holosun 407K X2 fits the Springfield Armory Hellcat Pro with an adapter plate: the Hellcat (RMSc footprint) → Holosun 407K / 507K from C&H Precision.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
The slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.
- Hellcat (RMSc footprint) → Holosun 407K / 507KC&H Precision ↗$25–60C&H sells a separate plate for the EPS / EPS Carry / SCS Carry.Plate screws M4 · optic screws not in C&H Precision's listing
What to buy
- Optic
- Holosun 407K X2 ($150–300)
- Plate
- The Hellcat (RMSc footprint) → Holosun 407K / 507K, from C&H Precision ($25–60).
- Screws
- Use the ones that come with the plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
- All in
- $175–360 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M4From C&H Precision, Hellcat (RMSc footprint) → Holosun 407K / 507K ↗, checked against it September 30, 2026 (the optics named and the included hardware).
- Torque
- per plate maker, not on file hereNot on file. What would settle it.
Cite this joint The Holosun 407K X2 on the Springfield Armory Hellcat Pro, Plate to slide: thread M4; torque not on file. Source: C&H Precision, Hellcat (RMSc footprint) → Holosun 407K / 507K (https://chpws.com/product/springfield-hellcat-to-holosun-407k-507k-adapter-plate/), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-springfield-armory-hellcat-pro/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Holosun 407K X2 on the Springfield Armory Hellcat Pro, Optic to plate: thread not on file; torque not on file; driver T10. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-springfield-armory-hellcat-pro/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Springfield Armory Hellcat Pro
- Optic
- Holosun 407K X2
- Footprint
- Holosun K
- Slide
- Springfield Hellcat OSP cut (Micro footprint)
- Mount
- Adapter plate required
Parts to order
| 1 × | Holosun 407K X2Holosun K footprint · 6 MOA | $150–300 |
| 1 × | Hellcat (RMSc footprint) → Holosun 407K / 507KC&H Precision — C&H sells a separate plate for the EPS / EPS Carry / SCS Carry. | $25–60 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $175–360 |
Where to buy
| Holosun 407K X2Holosun K footprint | Holosun ↗ |
| Hellcat (RMSc footprint) → Holosun 407K / 507KC&H Precision | C&H Precision — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M4 | Supplied with the plate. If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths. |
| Optic → plate | per plate maker, not on file here | Supplied with the plate, not the optic. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T10, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Plate-to-slide torque
- Not published for this plate. Use the plate maker's figure.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Springfield Armory Hellcat Pro with other optics
Every optic on the Springfield Armory Hellcat Pro, and how each mounts
The Holosun 407K X2 on other pistols
Direct (cross-fit)7
Plate in box2
Plate19
- GLOCK 19 Gen5 MOS
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- SIG Sauer P320 X-Carry
- GLOCK 17 Gen5 MOS
- GLOCK 48 MOS
- Walther PDP Full Size (1.0)
- Ruger RXM
- GLOCK 45 Gen5 MOS
- GLOCK 26 Gen5 MOS
- Smith & Wesson M&P Shield Plus Optics Ready
- Canik METE SFx
- SIG Sauer P320 XCompact
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Walther PDP Compact (1.0)
- CZ P-10 C Optics Ready
- Heckler & Koch VP9 Optics Ready
- CZ Shadow 2 Optics Ready
- Canik TTI Combat
Sources for this page (7)
- Slide Springfield Armory, Hellcat manual ↗
- Slide Springfield Armory, Hellcat Hardware Mounting Kit (Shield RMSc & JPoint) ↗
- Slide SIG Sauer, ROMEOZero-ELITE operator's manual (REV00) ↗
- Slide Springfield Armory, Hellcat Pro OSP (slide milled for the Springfield Micro footprint) ↗
- Slide HEX by Springfield Armory, HEX Wasp (Springfield Micro, Shield RMSc footprint) ↗
- Slide C&H Precision, Hellcat to Holosun 407K / 507K ↗
- Optic Holosun, HS407K-X2 (in the box: 2× M4×12, 2× #6-32×7.4) ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Holosun 407K X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Springfield Armory Hellcat Pro’s slide: slide screw thread, the footprint's name and the optics Springfield names checked against Springfield's Hellcat manual, hardware kit page and Hellcat Pro OSP page, and HEX's Wasp page on September 30, 2026. The Hellcat (RMSc footprint) → Holosun 407K / 507K: the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026.