Does the Holosun 407K X2 fit the SIG Sauer P320 XCompact?
Yes, the Holosun 407K X2 fits the SIG Sauer P320 XCompact with an adapter plate: the P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight S from C&H Precision.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
The slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.
- P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight SC&H Precision ↗$25–60Plate screws not in C&H Precision's listing · optic screws M4
What to buy
- Optic
- Holosun 407K X2 ($150–300)
- Plate
- The P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight S, from C&H Precision ($25–60).
- Screws
- M4, from the optic's or plate's box. Blue threadlocker, never red.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
- All in
- $175–360 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M4 × 0.7From SIG Sauer, ROMEO1PRO operator's manual (REV05) ↗; SIG Sauer, ROMEO2 operator's manual (REV04) ↗, checked against them September 30, 2026 (slide screw thread; footprint screw, torque and driver).
- Torque
- per plate instructions
Cite this joint The Holosun 407K X2 on the SIG Sauer P320 XCompact, Plate to slide: thread M4 × 0.7; torque per plate instructions. Source: SIG Sauer, ROMEO1PRO operator's manual (REV05) (https://www.sigsauer.com/media/sigsauer/resources/OPERATORS_MANUAL_ROMEO1PRO_7401786-01_REV05_WEB_FILE.pdf), checked 2026-09-30; SIG Sauer, ROMEO2 operator's manual (REV04) (https://www.sigsauer.com/media/sigsauer/resources/operators_manual-romeo2-7402277-01-rev04-lr.pdf), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-sig-sauer-p320-xcompact/#joint-plate-slide
Optic → plate
- Thread
- M4From C&H Precision, P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight S ↗, checked against it September 30, 2026 (the optics named and the included hardware).
- Torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Holosun 407K X2 on the SIG Sauer P320 XCompact, Optic to plate: thread M4; torque not on file; driver T10. Source: C&H Precision, P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight S (https://chpws.com/product/sig-p320-rx-pro-series-axg-to-holosun-407k-507k/), checked 2026-09-30. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-sig-sauer-p320-xcompact/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- SIG Sauer P320 XCompact
- Optic
- Holosun 407K X2
- Footprint
- Holosun K
- Slide
- SIG P320 optic cut (Romeo1Pro pattern)
- Mount
- Adapter plate required
Parts to order
| 1 × | Holosun 407K X2Holosun K footprint · 6 MOA | $150–300 |
| 1 × | P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight SC&H Precision | $25–60 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $175–360 |
Where to buy
| Holosun 407K X2Holosun K footprint | Holosun ↗ |
| P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight SC&H Precision | C&H Precision — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M4 × 0.7 | Supplied with the plate. If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths. |
| Optic → plate | M4 | Supplied with the plate, not the optic. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T10, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The SIG Sauer P320 XCompact with other optics
Direct (cross-fit)1
Plate11
No fit1
Every optic on the SIG Sauer P320 XCompact, and how each mounts
The Holosun 407K X2 on other pistols
Direct (cross-fit)7
Plate in box2
Plate19
- GLOCK 19 Gen5 MOS
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- SIG Sauer P320 X-Carry
- GLOCK 17 Gen5 MOS
- GLOCK 48 MOS
- Walther PDP Full Size (1.0)
- Ruger RXM
- GLOCK 45 Gen5 MOS
- GLOCK 26 Gen5 MOS
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Walther PDP Compact (1.0)
- CZ P-10 C Optics Ready
- Heckler & Koch VP9 Optics Ready
- CZ Shadow 2 Optics Ready
- Canik TTI Combat
Sources for this page (4)
- Slide SIG Sauer, ROMEO1PRO operator's manual (REV05) ↗
- Slide SIG Sauer, ROMEO2 operator's manual (REV04) ↗
- Optic Holosun, HS407K-X2 (in the box: 2× M4×12, 2× #6-32×7.4) ↗
- Plate C&H Precision, P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight S ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Holosun 407K X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The SIG Sauer P320 XCompact’s slide: slide screw thread; footprint screw, torque and driver checked against SIG's ROMEO1PRO (REV05) and ROMEO2 (REV04) operator's manuals on September 30, 2026. The P320 → Holosun 407K / 507K / Vortex Defender-CCW / Olight Osight S: the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026.