Does the Leupold DeltaPoint Pro fit the SIG Sauer P320 XCompact?
Yes, the Leupold DeltaPoint Pro mounts straight to the SIG Sauer P320 XCompact with no adapter plate; the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Direct mount — cross-compatible
The slide is cut for SIG Romeo1Pro, and this footprint fits that cut with no adapter.
What to buy
- Optic
- Leupold DeltaPoint Pro ($300–450)
- Plate
- None: it mounts straight to the slide.
- Screws
- M4 × 0.7, from the optic's or plate's box. Blue threadlocker, never red.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: co-witnesses (estimated, why).
- All in
- $300–450 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Optic → slide
- Thread
- M4 × 0.7From SIG Sauer, ROMEO1PRO operator's manual (REV05) ↗; SIG Sauer, ROMEO2 operator's manual (REV04) ↗, checked against them September 30, 2026 (slide screw thread; footprint screw, torque and driver).
- Torque
- 20 in-lb (confirm current Leupold spec)The footprint's usual figure, but no document is linked for it here yet. What would settle it.
- Driver
- T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Leupold DeltaPoint Pro on the SIG Sauer P320 XCompact, Optic to slide: thread M4 × 0.7; torque 20 in-lb (confirm current Leupold spec); driver T15. Source: SIG Sauer, ROMEO1PRO operator's manual (REV05) (https://www.sigsauer.com/media/sigsauer/resources/OPERATORS_MANUAL_ROMEO1PRO_7401786-01_REV05_WEB_FILE.pdf), checked 2026-09-30; SIG Sauer, ROMEO2 operator's manual (REV04) (https://www.sigsauer.com/media/sigsauer/resources/operators_manual-romeo2-7402277-01-rev04-lr.pdf), checked 2026-09-30. No maker document on file for the torque or driver. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-sig-sauer-p320-xcompact/#joint-optic-slide
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- SIG Sauer P320 XCompact
- Optic
- Leupold DeltaPoint Pro
- Footprint
- Leupold DeltaPoint Pro
- Slide
- SIG P320 optic cut (Romeo1Pro pattern)
- Mount
- Direct mount — cross-compatible
Parts to order
| 1 × | Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint · 2.5 / 6 MOA or 7.5 MOA delta | $300–450 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only | $300–450 |
Where to buy
| Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint | Leupold ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Optic → slide | M4 × 0.7 | Supplied with the optic. With no plate in the stack, the screws that came with the optic are normally correct. The pistol's cover-plate screws are not optic screws; set them aside. |
On the bench before you start
- Torque wrench — covering 20 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the cover plate and set it aside with its screws.
- Degrease the slide cut and the optic base.
- Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
- Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The SIG Sauer P320 XCompact with other optics
Plate12
No fit1
Every optic on the SIG Sauer P320 XCompact, and how each mounts
The Leupold DeltaPoint Pro on other pistols
Plate in box3
Plate10
No fit13
- SIG Sauer P365XL
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- GLOCK 48 MOS
- SIG Sauer P365X
- SIG Sauer P365 Optics Ready
- SIG Sauer P365-XMACRO / XMACRO Comp
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- Taurus GX4 TORO / GX4XL
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
- Canik TTI Combat
Sources for this page (3)
- Slide SIG Sauer, ROMEO1PRO operator's manual (REV05) ↗
- Slide SIG Sauer, ROMEO2 operator's manual (REV04) ↗
- Optic Leupold, DeltaPoint Pro ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Leupold DeltaPoint Pro: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The SIG Sauer P320 XCompact’s slide: slide screw thread; footprint screw, torque and driver checked against SIG's ROMEO1PRO (REV05) and ROMEO2 (REV04) operator's manuals on September 30, 2026.