Home / Pistols / Walther PDP Compact (1.0) / Leupold DeltaPoint Pro

Does the Leupold DeltaPoint Pro fit the Walther PDP Compact (1.0)?

Yes, the Leupold DeltaPoint Pro fits the Walther PDP Compact (1.0) with an adapter plate: the PDP 1.0 → DeltaPoint Pro, a Walther factory part.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

The slide isn't cut for this pattern. One plate adapts it, listed below. The plate supplies the recoil posts the optic sits on.

What to buy

Optic
Leupold DeltaPoint Pro ($300–450)
Plate
The PDP 1.0 → DeltaPoint Pro, a Walther factory part ($25–60).
Screws
Use the ones that come with the plate.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
All in
$325–510 approximate street prices, September 2026
Same answer forThe Leupold DeltaPoint Pro goes on the Walther PDP Full Size (1.0), Walther PDP F-Series, Walther PDP Pro SD, Walther PDP Pro, Walther PDP Steel Frame and Walther PDP Compact F-Series the same way: they share this slide's optic cut.
SlideWalther PDP 1.0 optic cut
Optic footprintLeupold DeltaPoint Pro
Optic screwsper plate maker, not on file here · T15
Optic torqueper plate maker, not on file here (20 in-lb (confirm current Leupold spec) is the optic maker's figure for mounting it straight on a slide)
Plate to slideapproximately 2 Nm (17.7 in-lb)
Cost to mount$325–510

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
M3From Carl Walther, PDP pistols safety & instruction manual (2021, rev. a) ↗, checked against it September 30, 2026 (the plate screw thread and torque, and the cut's name).
Torque
approximately 2 Nm (17.7 in-lb)From Carl Walther, PDP pistols safety & instruction manual (2021, rev. a) ↗, checked against it September 30, 2026 (the plate screw thread and torque, and the cut's name).

Cite this joint The Leupold DeltaPoint Pro on the Walther PDP Compact (1.0), Plate to slide: thread M3; torque approximately 2 Nm (17.7 in-lb). Source: Carl Walther, PDP pistols safety & instruction manual (2021, rev. a) (https://carl-walther.com/uploads/media/manuals/285%2020%2004%20a%20PDP%20Intl.%20LR%20gesamt.pdf), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-walther-pdp-compact-1-0/#joint-plate-slide

Optic → plate

Thread
per plate maker, not on file hereNot on file. What would settle it.
Torque
per plate maker, not on file here (20 in-lb (confirm current Leupold spec) is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
Driver
T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Leupold DeltaPoint Pro on the Walther PDP Compact (1.0), Optic to plate: thread not on file; torque not on file; driver T15. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-walther-pdp-compact-1-0/#joint-optic-plate

Published for this exact pairing
  • Night Fision · lower 1/3 · front .469 / rear .494 in
Heights are front / rear in inches, as each sight maker measures its own sights. That's not a deck height, and it doesn't compare across makers to the thousandth. Absolute puts the front sight level with the dot; lower 1/3 and lower 1/5 sit it lower in the window. A sight maker sells a handful of fixed heights, so optics of similar height share one set: the same figures under two optics are the maker's chart saying so, not a copy.Night Fision — co-witness chart for the Walther PDP ↗
With the sights already on itStandard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. The published heights are for aftermarket sight sets, not factory irons, so "no co-witness" is the typical case rather than a guarantee: some optics still show factory-height irons in the lower third or lower fifth of the window.Taller sights made for this optic are the published ones above.
How this slide mounts an opticWalther sells its own plates for this cut (its "Gen1" plates, for the flat-bottomed cut), and C&H makes more. PDP 1.0 and PDP 2.0 plates are not interchangeable, so confirm which slide you have before ordering. Source: Walther Arms, PDP Gen1 Optic Plate, RMR (Generation 1 Optic Cut, flat bottom) ↗; Walther Arms, PDP Gen2 Optic Plate, Doctor (Generation 2 Optic Cut, lug bottom) ↗.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Walther PDP Compact (1.0)
Optic
Leupold DeltaPoint Pro
Footprint
Leupold DeltaPoint Pro
Slide
Walther PDP 1.0 optic cut
Mount
Adapter plate required

Parts to order

1 ×Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint · 2.5 / 6 MOA or 7.5 MOA delta$300–450
1 ×PDP 1.0 → DeltaPoint ProWalther factory — Walther's name for the footprint is "Leupold Delta Point Pro", and its manual numbers this mount base 04 (Leupold).$25–60
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$325–510

Where to buy

Leupold DeltaPoint ProLeupold DeltaPoint Pro footprintLeupold ↗
PDP 1.0 → DeltaPoint ProWalther factoryWalther factory — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideM3Supplied with the plate.
If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths.
Optic → plateper plate maker, not on file hereSupplied with the plate, not the optic.
Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy.

On the bench before you start

  • Torque wrench — covering 17.7 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slideapproximately 2 Nm (17.7 in-lb)
Optic torqueper plate maker, not on file here (20 in-lb (confirm current Leupold spec) is the optic maker's figure for mounting it straight on a slide)
Screwsper plate maker, not on file here
DriverT15
Interface2 screws, 4 corner recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Optic → plate thread
Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
Optic screw torque
Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (6)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Leupold DeltaPoint Pro: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Walther PDP Compact (1.0)’s slide: the plate screw thread and torque, and the cut's name checked against Carl Walther's PDP manual and Walther Arms' Gen 1 and Gen 2 plate listings on September 30, 2026. The PDP 1.0 → DeltaPoint Pro: the plate screw thread and torque, and the cut's name checked against Carl Walther's PDP manual and Walther Arms' Gen 1 and Gen 2 plate listings on September 30, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.