Does the Leupold DeltaPoint Pro fit the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)?
Yes, the Leupold DeltaPoint Pro fits the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in) on a plate that ships with the pistol (C.O.R.E. Plate 6 (DPP family)); the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Fits on the plate in the box
The C.O.R.E. Plate 6 (DPP family) that ships with the pistol adapts the slide to this footprint. Aftermarket plates are listed below too.
- C.O.R.E. Plate 6 (DPP family)S&W factory ↗in the boxpriced here and used on the build sheetS&W's guide: Leupold DeltaPoint Pro (S&W screw type E), EOTech EFLX, Vortex Defender-ST / XL, Bushnell RXS-100, and SIG's ROMEO2 and ROMEO1PRO.
What to buy
- Optic
- Leupold DeltaPoint Pro ($300–450)
- Plate
- None to buy: the C.O.R.E. Plate 6 (DPP family) ships with the pistol. Look in the box.
- Screws
- Look in the pistol's box with the plates; if there are none, buy a pair made for this plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
- All in
- $300–450 approximate street prices, September 2026
One other plate fits
- M&P 2.0 → DPP / EFLXC&H Precision ↗$25–60Plate screws not in C&H Precision's listing · optic screws #6-32
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it, for the C.O.R.E. Plate 6 (DPP family). Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate instructions
Cite this joint The Leupold DeltaPoint Pro on the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Plate to slide: thread not on file; torque per plate instructions. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-smith-and-wesson-m-and-p9-m2-0-optics-ready-4-25-4-6-5-in/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate maker, not on file here (20 in-lb (confirm current Leupold spec) is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Leupold DeltaPoint Pro on the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Optic to plate: thread not on file; torque not on file; driver T15. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-smith-and-wesson-m-and-p9-m2-0-optics-ready-4-25-4-6-5-in/#joint-optic-plate
- Night Fision · lower 1/3 · front .464 / rear .560 in
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height and the C.O.R.E. Plate 6 (DPP family). Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)
- Optic
- Leupold DeltaPoint Pro
- Footprint
- Leupold DeltaPoint Pro
- Slide
- S&W M&P C.O.R.E. / Optics Ready
- Mount
- Fits on the plate in the box
Parts to order
| 1 × | Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint · 2.5 / 6 MOA or 7.5 MOA delta | $300–450 |
| have | C.O.R.E. Plate 6 (DPP family)S&W factory — S&W's guide: Leupold DeltaPoint Pro (S&W screw type E), EOTech EFLX, Vortex Defender-ST / XL, Bushnell RXS-100, and SIG's ROMEO2 and ROMEO1PRO. | in the box |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only (plate ships with the pistol) | $300–450 |
Where to buy
| Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint | Leupold ↗ |
| C.O.R.E. Plate 6 (DPP family) | Ships with the pistol |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | per plate maker, not on file here | Supplied with the plate. Two kinds of short screw come with the pistol: these, for the plate, and the pair already holding the cover plate on the slide. They are different lengths, so keep them apart. |
| Optic → plate | per plate maker, not on file here | Look in the pistol's box, with the plates. If there are none, buy a pair made for this plate. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Plate → slide thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in) with other optics
Plate in box9
No fit1
Every optic on the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), and how each mounts
The Leupold DeltaPoint Pro on other pistols
Direct (cross-fit)5
Plate10
No fit13
- SIG Sauer P365XL
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- GLOCK 48 MOS
- SIG Sauer P365X
- SIG Sauer P365 Optics Ready
- SIG Sauer P365-XMACRO / XMACRO Comp
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- Taurus GX4 TORO / GX4XL
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
- Canik TTI Combat
Sources for this page (5)
- Slide Smith & Wesson, optic fitment guide: M&P M2.0 with C.O.R.E. plates (2025, v5) ↗
- Slide Smith & Wesson, M&P9 M2.0 Optics Ready Full Size product page ("Seven mounting plates included") ↗
- Optic Leupold, DeltaPoint Pro ↗
- Plate C&H Precision, M&P 2.0 → DPP / EFLX ↗
- Sights Night Fision, co-witness chart for the full-size M&P optics cut ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Leupold DeltaPoint Pro: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)’s slide: the plate for each optic, and the plates in the box checked against S&W's M&P M2.0 optic fitment guide (2025, v5) and product page on September 30, 2026. The C.O.R.E. Plate 6 (DPP family): the plate for each optic, and the plates in the box checked against S&W's M&P M2.0 optic fitment guide (2025, v5) and product page on September 30, 2026. The M&P 2.0 → DPP / EFLX: screw threads checked against the plate maker's own hardware list on September 28, 2026.