Does the Aimpoint ACRO P-2 fit the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)?

Yes, the Aimpoint ACRO P-2 fits the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in) with an adapter plate; two plates fit, and the cheapest is the M&P 2.0 → Steiner MPS (steel) from C&H Precision.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

Enclosed emitter

The slide isn't cut for this pattern. 2 plates adapt it, listed below. The plate gives the optic's clamp a rail to grip.

  • M&P 2.0 → Steiner MPS (steel)C&H Precision ↗$60–95priced here and used on the build sheetAlso the route for Aimpoint ACRO — same clamp interfacePlate screws #6-32 · optic screws not in C&H Precision's listing

What to buy

Optic
Aimpoint ACRO P-2 ($650+)
Plate
The M&P 2.0 → Steiner MPS (steel), from C&H Precision ($60–95).
Screws
Cross-bolt clamp, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
All in
$710–995 approximate street prices, September 2026
One other plate fits
  • Steel plates — MPS / RMR / KAthena Precision ↗$60–95Steel rather than aluminium; worth it on a comped gun
SlideS&W M&P C.O.R.E. / Optics Ready
Optic footprintAimpoint ACRO
Screws and torque below are forM&P 2.0 → Steiner MPS (steel) (C&H Precision); other plates list their own above
Optic screwsCross-bolt clamp · T10 / hex per model
Optic torqueper Aimpoint manual
Plate to slideper plate instructions
Cost to mount$710–995

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it, for the M&P 2.0 → Steiner MPS (steel). Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
#6-32From C&H Precision, M&P 2.0 → Steiner MPS (steel) ↗, checked against it September 28, 2026 (screw threads).
Torque
per plate instructions

Cite this joint The Aimpoint ACRO P-2 on the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Plate to slide: thread #6-32; torque per plate instructions. Source: C&H Precision, M&P 2.0 → Steiner MPS (steel) (https://chpws.com/product/sw-m2-0-c-o-r-e-to-steiner-mps-steel/), checked 2026-09-28. Optic Mounting, https://opticmounting.com/fit/aimpoint-acro-p-2-on-smith-and-wesson-m-and-p9-m2-0-optics-ready-4-25-4-6-5-in/#joint-plate-slide

Optic → interface

Thread
Cross-bolt clamp
Torque
per Aimpoint manual
Driver
T10 / hex per modelThe footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Aimpoint ACRO P-2 on the Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Optic to interface: thread Cross-bolt clamp; torque per Aimpoint manual; driver T10 / hex per model. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/aimpoint-acro-p-2-on-smith-and-wesson-m-and-p9-m2-0-optics-ready-4-25-4-6-5-in/#joint-optic-interface

Published for this exact pairing
  • Night Fision · lower 1/3 · front .464 / rear .560 in
Heights are front / rear in inches, as each sight maker measures its own sights. That's not a deck height, and it doesn't compare across makers to the thousandth. Absolute puts the front sight level with the dot; lower 1/3 and lower 1/5 sit it lower in the window. A sight maker sells a handful of fixed heights, so optics of similar height share one set: the same figures under two optics are the maker's chart saying so, not a copy.Night Fision — co-witness chart for the full-size M&P optics cut ↗
With the sights already on itStandard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. The published heights are for aftermarket sight sets, not factory irons, so "no co-witness" is the typical case rather than a guarantee: some optics still show factory-height irons in the lower third or lower fifth of the window.Taller sights made for this optic are the published ones above.
How this slide mounts an opticA generic pocket plus a plate that supplies the recoil posts. S&W's product page says seven mounting plates come with the pistol, and its optic fitment guide numbers them and names the plate for each optic. The aftermarket covers what the kit misses.
About this optic50,000-hour runtime on one cell. Small window, sealed housing.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height and the M&P 2.0 → Steiner MPS (steel). Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)
Optic
Aimpoint ACRO P-2
Footprint
Aimpoint ACRO
Slide
S&W M&P C.O.R.E. / Optics Ready
Mount
Adapter plate required

Parts to order

1 ×Aimpoint ACRO P-2Aimpoint ACRO footprint · 3.5 MOA$650+
1 ×M&P 2.0 → Steiner MPS (steel)C&H Precision — Also the route for Aimpoint ACRO — same clamp interface$60–95
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$710–995

Where to buy

Aimpoint ACRO P-2Aimpoint ACRO footprintAimpoint — this item ↗
M&P 2.0 → Steiner MPS (steel)C&H PrecisionC&H Precision — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slide#6-32Supplied with the plate.
The one screwed joint in this stack, so it gets the threadlocker and the torque check. Keep the pistol's cover-plate screws apart from these.
Optic → interfaceCross-bolt clampSupplied with the optic.
The ACRO clamps rather than bolting through, so there's no screw length to get wrong. Torque the cross-bolt to Aimpoint's figure.

On the bench before you start

  • Torque wrench — set to the figure in your optic's manual
  • Driver bits — T10 / hex per model, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slideper plate instructions
Optic torqueper Aimpoint manual
ScrewsCross-bolt clamp
DriverT10 / hex per model
InterfaceClamp interface with recoil shoulder — not a screw-and-lug pattern

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Set the optic on the plate's rail and tighten its cross-bolt clamp to Aimpoint's figure. There are no optic screws to fit.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (5)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)’s slide: the plate for each optic, and the plates in the box checked against S&W's M&P M2.0 optic fitment guide (2025, v5) and product page on September 30, 2026. The M&P 2.0 → Steiner MPS (steel): screw threads checked against the plate maker's own hardware list on September 28, 2026. Not individually re-checked since it was compiled (September 2026): the optic’s figures and the plate.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.