Home / Pistols / Canik METE SFx / Aimpoint ACRO P-2

Does the Aimpoint ACRO P-2 fit the Canik METE SFx?

Yes, the Aimpoint ACRO P-2 fits the Canik METE SFx with an adapter plate: the METE → ACRO from Calculated Kinetics.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Adapter plate required

Enclosed emitter

The slide isn't cut for this pattern. One plate adapts it, listed below. The plate gives the optic's clamp a rail to grip.

  • METE → ACROCalculated Kinetics ↗$60–95Calculated Kinetics lists an ACRO-footprint plate for the METE. Canik lists no ACRO interface for it.

What to buy

Optic
Aimpoint ACRO P-2 ($650+)
Plate
The METE → ACRO, from Calculated Kinetics ($60–95).
Screws
Cross-bolt clamp, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: low at best (estimated, why).
All in
$710–995 approximate street prices, September 2026
Same answer forThe Aimpoint ACRO P-2 goes on the Canik METE SFT, Canik METE SF and Canik METE SFT Pro the same way: they share this slide's optic cut.
SlideCanik METE optic cut (RMSc plus RMRcc or RMR)
Optic footprintAimpoint ACRO
Optic screwsCross-bolt clamp · T10 / hex per model
Optic torqueper Aimpoint manual
Plate to slideper plate maker, not on file here
Cost to mount$710–995

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
set by the slide
Torque
per plate maker, not on file hereNot on file. What would settle it.

Cite this joint The Aimpoint ACRO P-2 on the Canik METE SFx, Plate to slide: thread set by the slide; torque not on file. Optic Mounting, https://opticmounting.com/fit/aimpoint-acro-p-2-on-canik-mete-sfx/#joint-plate-slide

Optic → interface

Thread
Cross-bolt clamp
Torque
per Aimpoint manual
Driver
T10 / hex per modelThe footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Aimpoint ACRO P-2 on the Canik METE SFx, Optic to interface: thread Cross-bolt clamp; torque per Aimpoint manual; driver T10 / hex per model. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/aimpoint-acro-p-2-on-canik-mete-sfx/#joint-optic-interface

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Low at best. An enclosed emitter on a plate sits tall, so suppressor-height irons land at the very bottom of the window or below it: Night Fision lists its .290 in front sight as a lower 1/5 co-witness for an ACRO P-2 on GLOCK's MOS plate, and taller optics lose them. Sights taller than suppressor height are the usual fix. This optic's window runs small (15 × 15 mm), so a front sight slightly off the ideal height is more likely to miss it. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
How this slide mounts an opticCanik cuts the METE slide for two patterns at once. One is Shield RMSc, on every METE. The other changed during production: Canik lists RMRcc on earlier slides and RMR on later ones (METE SFT from serial 25CC08376, METE SFT Pro from 25CY04801, METE SFx from 26BY00001, METE SF after 25BU15401, which it words as "RMSc and RMR"). Canik's manuals say the pistol comes with three optic interfaces (numbers 1, 2 and 3): 1 and 2 take the RMSc pattern optics (Canik names Shield RMS, RMSc and SMSc, JPoint, SIG ROMEOZero, Sightmark Mini Shot A-Spec M3, Swampfox Sentinel and the Mecanik MO1), and 3 takes the RMR pattern. An optic goes on one of them, not straight onto the slide. Canik says to use only the screws that came with the pistol to mount an optic; for the RMR-pattern interface 3, only the #6-32 screws in the optic's own box, not the M3 or M4 screws packed for other footprints. Canik's product pages say a pistol's case holds two or three interfaces, so check the case. Only the RMSc pattern is listed as a fit here: the second one depends on your serial, so check it against Canik's product page before buying an RMR or RMRcc optic. Canik names no Holosun K optic, and no Canik document gives a torque for the interfaces or the optic screws. Source: Canik, METE SFT product page (serial numbers by optic footprint) ↗; Canik, METE SFx product page ↗; Canik, METE SF product page ↗; Canik, METE SFT Pro product page ↗.
About this optic50,000-hour runtime on one cell. Small window, sealed housing.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Canik METE SFx
Optic
Aimpoint ACRO P-2
Footprint
Aimpoint ACRO
Slide
Canik METE optic cut (RMSc plus RMRcc or RMR)
Mount
Adapter plate required

Parts to order

1 ×Aimpoint ACRO P-2Aimpoint ACRO footprint · 3.5 MOA$650+
1 ×METE → ACROCalculated Kinetics — Calculated Kinetics lists an ACRO-footprint plate for the METE. Canik lists no ACRO interface for it.$60–95
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic + plate$710–995

Where to buy

Aimpoint ACRO P-2Aimpoint ACRO footprintAimpoint — this item ↗
METE → ACROCalculated KineticsCalculated Kinetics — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideset by the slideSupplied with the plate.
The one screwed joint in this stack, so it gets the threadlocker and the torque check. Keep the pistol's cover-plate screws apart from these.
Optic → interfaceCross-bolt clampSupplied with the optic.
The ACRO clamps rather than bolting through, so there's no screw length to get wrong. Torque the cross-bolt to Aimpoint's figure.

On the bench before you start

  • Torque wrench — set to the figure in your optic's manual
  • Driver bits — T10 / hex per model, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slideper plate maker, not on file here
Optic torqueper Aimpoint manual
ScrewsCross-bolt clamp
DriverT10 / hex per model
InterfaceClamp interface with recoil shoulder — not a screw-and-lug pattern

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Plate-to-slide torque
Not published for this plate. Use the plate maker's figure.
Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Set the optic on the plate's rail and tighten its cross-bolt clamp to Aimpoint's figure. There are no optic screws to fit.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (9)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Canik METE SFx’s slide: optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link checked against Canik's owner's manuals (METE SFT, SFx, SF and SFT Pro; TP9 SFx; SFx Rival and Rival-S; TTI Combat; TP9 Elite SC), its product and parts pages on canik.com, and Calculated Kinetics' own listings on October 1, 2026. The METE → ACRO: optic interface plates: which optics each takes, what ships with the pistol, the screws Canik names, and the listing link checked against Canik's owner's manuals (METE SFT, SFx, SF and SFT Pro; TP9 SFx; SFx Rival and Rival-S; TTI Combat; TP9 Elite SC), its product and parts pages on canik.com, and Calculated Kinetics' own listings on October 1, 2026. Not individually re-checked since it was compiled (September 2026): the optic’s figures.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.