Does the Leupold DeltaPoint Pro fit the GLOCK 45 Gen5 MOS?
Yes, the Leupold DeltaPoint Pro fits the GLOCK 45 Gen5 MOS with an adapter plate; three plates fit, and the cheapest is the MOS Plate 04, a GLOCK factory part.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
The slide isn't cut for this pattern. 3 plates adapt it, listed below. The plate supplies the recoil posts the optic sits on.
- MOS Plate 04GLOCK factory ↗$13–25priced here and used on the build sheetLeupold DeltaPoint Pro and DPP-pattern optics such as the EOTech EFLXPlate screws M3 · optic screws M4 · from GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗
What to buy
- Optic
- Leupold DeltaPoint Pro ($300–450)
- Plate
- The MOS Plate 04, a GLOCK factory part ($13–25).
- Screws
- M4 screws. Not in GLOCK's plate set, which holds the plate screws only. GLOCK says to fit the optic as its maker directs, with screws that do not come through the 2.5 mm plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Taller sights: sight makers publish heights for this exact pair, below.
- All in
- $313–475 approximate street prices, September 2026
Two other plates fit
- V4 MIL/LEO (one SKU per footprint)C&H Precision$25–60The same plate for other footprints: order the version made for your optic.
- Type A / Type BOptics Spot$25–60Type A covers RMSc / DPP / Docter; Type B covers RMR / RTS2.
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it, for the MOS Plate 04. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M3From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
- Torque
- 13.1 in-lb (1.5 Nm)From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
Cite this joint The Leupold DeltaPoint Pro on the GLOCK 45 Gen5 MOS, Plate to slide: thread M3; torque 13.1 in-lb (1.5 Nm). Source: GLOCK, accompanying sheet for MOS adapter plates (10/22) (https://eu.glock.com/en/-/media/Global/EU/GLOCK-GmbH-2019/ContactandSupport/Download-Area/Instruction_MOS_Adapter_Plate.ashx), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-glock-45-gen5-mos/#joint-plate-slide
Optic → plate
- Thread
- M4From GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗, checked against it September 30, 2026 (plate and optic screw threads, plate screw torque).
- Torque
- per plate maker, not on file here (20 in-lb (confirm current Leupold spec) is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Leupold DeltaPoint Pro on the GLOCK 45 Gen5 MOS, Optic to plate: thread M4; torque not on file; driver T15. Source: GLOCK, accompanying sheet for MOS adapter plates (10/22) (https://eu.glock.com/en/-/media/Global/EU/GLOCK-GmbH-2019/ContactandSupport/Download-Area/Instruction_MOS_Adapter_Plate.ashx), checked 2026-09-30. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-glock-45-gen5-mos/#joint-optic-plate
- Night Fision · lower 1/3 · front .469 / rear .494 in
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height and the MOS Plate 04. Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- GLOCK 45 Gen5 MOS
- Optic
- Leupold DeltaPoint Pro
- Footprint
- Leupold DeltaPoint Pro
- Slide
- GLOCK MOS — standard & full size
- Mount
- Adapter plate required
Parts to order
| 1 × | Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint · 2.5 / 6 MOA or 7.5 MOA delta | $300–450 |
| 1 × | MOS Plate 04GLOCK factory — Leupold DeltaPoint Pro and DPP-pattern optics such as the EOTech EFLX | $13–25 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $313–475 |
Where to buy
| Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint | Leupold ↗ |
| MOS Plate 04GLOCK factory | GLOCK factory — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M3 | Supplied with the pistol, in the box with the cover plate. If your pistol shipped with a cover plate, keep its screws apart from these: plate screws and cover-plate screws are different lengths. |
| Optic → plate | M4 | Not in GLOCK's plate set, which holds the plate screws only. GLOCK says to fit the optic as its maker directs, with screws that do not come through the 2.5 mm plate. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — covering 13.1 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The GLOCK 45 Gen5 MOS with other optics
Every optic on the GLOCK 45 Gen5 MOS, and how each mounts
The Leupold DeltaPoint Pro on other pistols
Direct (cross-fit)5
Plate in box3
Plate9
No fit13
- SIG Sauer P365XL
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- GLOCK 48 MOS
- SIG Sauer P365X
- SIG Sauer P365 Optics Ready
- SIG Sauer P365-XMACRO / XMACRO Comp
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- Taurus GX4 TORO / GX4XL
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
- Canik TTI Combat
Sources for this page (4)
- Slide GLOCK, accompanying sheet for MOS adapter plates (10/22) ↗
- Optic Leupold, DeltaPoint Pro ↗
- Plate GLOCK factory, MOS Plate 04 ↗
- Sights Night Fision, co-witness chart for GLOCK 17/19/26/34/45 ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Leupold DeltaPoint Pro: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The GLOCK 45 Gen5 MOS’s slide: plate and optic screw threads, plate screw torque checked against GLOCK's accompanying sheet for MOS adapter plates (10/22) on September 30, 2026. The MOS Plate 04: plate and optic screw threads, plate screw torque checked against GLOCK's accompanying sheet for MOS adapter plates (10/22) on September 30, 2026. Not individually re-checked since it was compiled (September 2026): 2 plates.