Home / Guides / Which GLOCK MOS plate

Which GLOCK MOS plate do I need?

By Andrew Terrebonne. Published September 22, 2026; updated October 1, 2026.

The one for your optic’s footprint. Standard-frame MOS slides ship with MOS Plate 02 (Trijicon RMR pattern) in the box, and the 10 mm and .45 slides with MOS Plate 06, its large-frame equivalent. The other factory plates are sold separately, and aftermarket plates cover the footprints GLOCK doesn’t.

Plate to slide13.1 in-lb (1.5 Nm)
Standard-frame slides12
Large-frame slides4
Optics that fit a MOS slide71 of 77
Plate screwsSupplied with the pistol, in the box with the cover plate.

Standard and full-size frames

GLOCK's 9 mm, .40 and .357 MOS slides (Gen4 and Gen5) take its 25.5 mm plates. Recent MOS pistols come with plate 02 (the RMR pattern); earlier ones came with a set, so look in your box before ordering. Plates 01, 03 and 04 are sold separately.

PlateGives youOptics tracked here it carriesSource
MOS Plate 01Docter / Noblex9 optics
Vortex Venom, Springfield Armory Hex Dragonfly, Vortex Viper, Burris FastFire 3, Burris FastFire 4, Noblex Sight III / Docter Sight C and 3 more
GLOCK factory ↗
MOS Plate 02
ships with the pistol
Trijicon RMR18 optics
Trijicon RMR Type 2, Trijicon RMR HD, Trijicon SRO, Holosun 507C X2, Holosun 407C X2, Holosun 508T X2 and 12 more
GLOCK factory ↗
MOS Plate 03C-More RTS2 / STS22 optics
C-More RTS2, C-More STS2
GLOCK factory ↗
MOS Plate 04Leupold DeltaPoint Pro7 optics
Leupold DeltaPoint Pro, Vortex Defender-ST, Vortex Defender-XL, Vortex Defender-SL, EOTECH EFLX Mini, Bushnell RXS-100 and 1 more
GLOCK factory ↗
ROMEO2 GLOCK MOS adapter plate (SOR2M102)SIG Romeo21 optic
SIG Sauer ROMEO2
SIG Sauer
V4 MIL/LEO → Trijicon RMR / SRO / Holosun 407C / 507C / 508TTrijicon RMR18 optics
Trijicon RMR Type 2, Trijicon RMR HD, Trijicon SRO, Holosun 507C X2, Holosun 407C X2, Holosun 508T X2 and 12 more
C&H Precision ↗
V4 MIL/LEO (one SKU per footprint)Leupold DeltaPoint Pro, Aimpoint ACRO, Holosun K, Shield RMSc, Holosun 509T, Trijicon RMRcc, SIG Romeo1Pro, Trijicon RCR40 optics
Shield Sights RMSc, Shield Sights RMS2, SIG Sauer ROMEOZero Elite, SIG Sauer ROMEOZero, Vortex Defender-CCW, Swampfox Sentinel II and 34 more
C&H Precision
Type A / Type BShield RMSc, Docter / Noblex, Leupold DeltaPoint Pro, Trijicon RMR, C-More RTS2 / STS251 optics
Trijicon RMR Type 2, Trijicon RMR HD, Trijicon SRO, Holosun 507C X2, Holosun 407C X2, Holosun 508T X2 and 45 more
Optics Spot
MOS → RCR (steel)Trijicon RCR1 optic
Trijicon RCR
Athena Precision ↗

Counted on the GLOCK 19 Gen5 MOS (its page); every slide below shares its cut.

10 mm and .45 frames

27.5 mm plates. Same four footprints as the standard frames, numbered 05 through 08.

Counted on the GLOCK 20 Gen5 MOS (10 mm) (its page); every slide below shares its cut.

No plate at all

These mount straight to the MOS pocket, removing the plate and the joint most likely to work loose:

No route onto a MOS slide

No plate tracked here takes these:

GLOCKs this doesn’t cover

GLOCK Gen6 ORSGLOCK's Gen6 replaces MOS: the standard-frame G17, G19 and G45 come with three polymer plates (02, 03, 04), and the optic screws directly into the slide through the plate, with no metal plate in between. GLOCK's sheet gives the thread by plate and no torque, and says to use the optic maker's own screws and directions.
The slim GLOCKs (43X and 48)No MOS plates: the slide is cut for the optic directly, and the two slim cuts are tapped for different screws. GLOCK Slimline MOS (43X / 48): GLOCK says the standard Slimline MOS cut takes M4 screws; SIG's ROMEOZero-ELITE manual gives them as M4 × 0.7 for the 43X MOS.GLOCK Slimline MOS-K: Tapped M3, not the M4 of the earlier Slimline MOS. The two slim GLOCK cuts look alike but take different screws; mixing them up is the most common cross-threading mistake on slim GLOCKs.

Shield RMSc vs Holosun K covers the footprints those slides take.

For your pistol and optic

Pick your GLOCK and your optic for the exact plate, both torque figures and a build sheet.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.