Does the Leupold DeltaPoint Pro fit the GLOCK 17 / 19 / 45 Gen6 (ORS)?
Yes, the Leupold DeltaPoint Pro fits the GLOCK 17 / 19 / 45 Gen6 (ORS) on a plate that ships with the pistol (ORS Plate 04); the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Fits on the plate in the box
The ORS Plate 04 that ships with the pistol adapts the slide to this footprint. Aftermarket plates are listed below too.
- ORS Plate 04GLOCK factory ↗in the boxpriced here and used on the build sheetGLOCK's sheet says Leupold and EOTech; its optic table names the Leupold DPP, EOTech EFLX and Vortex Defender-ST / XL. One of the three plates in the Gen6 box.Plate screws None: the plate has no screws of its own · optic screws M4 (into the slide, through the plate) · plate screws at None: GLOCK gives no plate screws or torque · optic screws at per optic manual (GLOCK gives no figure) · from GLOCK, Optic Ready (OR) Plates Set sheet (01/26) ↗
What to buy
- Optic
- Leupold DeltaPoint Pro ($300–450)
- Plate
- None to buy: the ORS Plate 04 ships with the pistol. Look in the box.
- Screws
- M4 (into the slide, through the plate) screws. Not in GLOCK's plate set. GLOCK's manual says to use the optic maker's own mounting screws.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
- All in
- $300–450 approximate street prices, September 2026
Two other plates fit
- Gen 6 MIL/LEO → Leupold DeltaPoint Pro / EOTech EFLXC&H Precision ↗$60–95Aluminium. C&H packs M4 optic screws for the DeltaPoint Pro and a shorter set for the EFLX and Vortex Defender-ST / XL.Plate screws not in C&H Precision's listing · optic screws M4
- OPF-G6, DPPForward Controls Design ↗$60–9517-4 stainless steel. FCD guarantees the current batch on the Leupold DeltaPoint Pro and EOTech EFLX only; it says a later batch will take the Vortex Defender.Plate screws not in Forward Controls Design's listing · optic screws M4 (into the slide)
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it, for the ORS Plate 04. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- None: the plate has no screws of its own
- Torque
- None: GLOCK gives no plate screws or torque
Cite this joint The Leupold DeltaPoint Pro on the GLOCK 17 / 19 / 45 Gen6 (ORS), Plate to slide: thread None: the plate has no screws of its own; torque None: GLOCK gives no plate screws or torque. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-glock-17-19-45-gen6-ors/#joint-plate-slide
Optic → plate
- Thread
- M4 (into the slide, through the plate)From GLOCK, Optic Ready (OR) Plates Set sheet (01/26) ↗, checked against it October 1, 2026 (screw threads, plate hardware and which optics each plate takes).
- Torque
- per optic manual (GLOCK gives no figure)
- Driver
- T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Leupold DeltaPoint Pro on the GLOCK 17 / 19 / 45 Gen6 (ORS), Optic to plate: thread M4 (into the slide, through the plate); torque per optic manual (GLOCK gives no figure); driver T15. Source: GLOCK, Optic Ready (OR) Plates Set sheet (01/26) (https://eu-assets.contentstack.com/v3/assets/bltf7171cc1cfc1a31f/blt9ac426e56af47ddd/69714e41d5cee4e127d4678b/OR_Adapter-Set_Gen6_012026.pdf), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-glock-17-19-45-gen6-ors/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height and the ORS Plate 04. Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Optic
- Leupold DeltaPoint Pro
- Footprint
- Leupold DeltaPoint Pro
- Slide
- GLOCK Gen6 ORS
- Mount
- Fits on the plate in the box
Parts to order
| 1 × | Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint · 2.5 / 6 MOA or 7.5 MOA delta | $300–450 |
| have | ORS Plate 04GLOCK factory — GLOCK's sheet says Leupold and EOTech; its optic table names the Leupold DPP, EOTech EFLX and Vortex Defender-ST / XL. One of the three plates in the Gen6 box. | in the box |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only (plate ships with the pistol) | $300–450 |
Where to buy
| Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint | Leupold ↗ |
| ORS Plate 04 | Ships with the pistol |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | None: the plate has no screws of its own | None: GLOCK's sheet has you seat the polymer plate in the slide and fit the optic through it. It says not to reuse the cover-plate screws to hold a plate. GLOCK's sheet gives this plate no screws: it seats on the slide and the optic goes through it. The cover-plate screws you took off are not for it. |
| Optic → plate | M4 (into the slide, through the plate) | Not in GLOCK's plate set. GLOCK's manual says to use the optic maker's own mounting screws. GLOCK says to use the optic maker's own mounting screws and to install the optic to its maker's directions. They go through this plate and into the slide, at the thread above. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The GLOCK 17 / 19 / 45 Gen6 (ORS) with other optics
Every optic on the GLOCK 17 / 19 / 45 Gen6 (ORS), and how each mounts
The Leupold DeltaPoint Pro on other pistols
Direct (cross-fit)5
Plate in box2
Plate10
No fit13
- SIG Sauer P365XL
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- GLOCK 48 MOS
- SIG Sauer P365X
- SIG Sauer P365 Optics Ready
- SIG Sauer P365-XMACRO / XMACRO Comp
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- Taurus GX4 TORO / GX4XL
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
- Canik TTI Combat
Sources for this page (9)
- Slide GLOCK, Optic Ready (OR) Plates Set sheet (01/26) ↗
- Slide GLOCK, Optic Ready System page (Gen6 optic table) ↗
- Slide GLOCK, instructions for use, Gen6 (10-25) ↗
- Slide GLOCK, Gen6 optic ready page (set contents) ↗
- Slide GLOCK, announcement of the 6th Generation (2025-12-06) ↗
- Optic Leupold, DeltaPoint Pro ↗
- Plate GLOCK factory, ORS Plate 04 ↗
- Plate C&H Precision, Gen 6 MIL/LEO → Leupold DeltaPoint Pro / EOTech EFLX ↗
- Plate Forward Controls Design, OPF-G6, DPP ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Leupold DeltaPoint Pro: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The GLOCK 17 / 19 / 45 Gen6 (ORS)’s slide: screw threads, plate hardware and which optics each plate takes checked against GLOCK's OR plates set sheet (01/26) and Optic Ready System page; C&H's and Trijicon's own listings on October 1, 2026. The ORS Plate 04: screw threads, plate hardware and which optics each plate takes checked against GLOCK's OR plates set sheet (01/26) and Optic Ready System page; C&H's and Trijicon's own listings on October 1, 2026. The Gen 6 MIL/LEO → Leupold DeltaPoint Pro / EOTech EFLX: footprints, the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026. The OPF-G6, DPP: footprints, the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026.