Does the Trijicon SRO fit the GLOCK 17 / 19 / 45 Gen6 (ORS)?

Yes, the Trijicon SRO fits the GLOCK 17 / 19 / 45 Gen6 (ORS) on a plate that ships with the pistol (ORS Plate 02); the optic is the only part to buy.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Fits on the plate in the box

The ORS Plate 02 that ships with the pistol adapts the slide to this footprint. Aftermarket plates are listed below too.

  • ORS Plate 02GLOCK factory ↗in the boxpriced here and used on the build sheetGLOCK's sheet says Trijicon, Holosun (except the 509) and Ameriglo; its optic table names the RMR, RCR, RMR HD, SRO, Holosun 508T, 407C and 507C / Comp, and C&H Precision. One of the three plates in the Gen6 box.Plate screws None: the plate has no screws of its own · optic screws 6-32 UNC (into the slide, through the plate) · plate screws at None: GLOCK gives no plate screws or torque · optic screws at per optic manual (GLOCK gives no figure) · from GLOCK, Optic Ready (OR) Plates Set sheet (01/26) ↗

What to buy

Optic
Trijicon SRO ($450–650)
Plate
None to buy: the ORS Plate 02 ships with the pistol. Look in the box.
Screws
6-32 UNC (into the slide, through the plate) screws. Not in GLOCK's plate set. GLOCK's manual says to use the optic maker's own mounting screws.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
All in
$450–650 approximate street prices, September 2026
Two other plates fit
  • Gen 6 MIL/LEO → Trijicon RMR / RMR HD / SRO / RCR / Holosun 407C / 507C / 507COMP / 508TC&H Precision ↗$60–95Aluminium. Replaces the ORS insert. C&H packs two sets of 6-32 optic screws, one for the Holosun optics and one for the Trijicon ones.Plate screws not in C&H Precision's listing · optic screws 6-32
  • OPF-G6, RMRForward Controls Design ↗$60–9517-4 stainless steel. FCD makes and guarantees it for Trijicon's own RMR, RMR HD, SRO and RCR only. The original RMR needs a sealing plate; the RMR HD and SRO do not. Its 6-32 screws go through the plate into the slide.Plate screws not in Forward Controls Design's listing · optic screws 6-32 (through the plate into the slide) · optic screws at 13–15 in-lb (FCD)
SlideGLOCK Gen6 ORS
Optic footprintTrijicon RMR
Screws and torque below are forORS Plate 02 (GLOCK factory); other plates list their own above
Optic screws6-32 UNC (into the slide, through the plate) · T10 / T15
Optic torqueper optic manual (GLOCK gives no figure)
Plate to slideNone: GLOCK gives no plate screws or torque
Cost to mount$450–650

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it, for the ORS Plate 02. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Plate → slide

Thread
None: the plate has no screws of its own
Torque
None: GLOCK gives no plate screws or torque

Cite this joint The Trijicon SRO on the GLOCK 17 / 19 / 45 Gen6 (ORS), Plate to slide: thread None: the plate has no screws of its own; torque None: GLOCK gives no plate screws or torque. Optic Mounting, https://opticmounting.com/fit/trijicon-sro-on-glock-17-19-45-gen6-ors/#joint-plate-slide

Optic → plate

Thread
6-32 UNC (into the slide, through the plate)From GLOCK, Optic Ready (OR) Plates Set sheet (01/26) ↗, checked against it October 1, 2026 (screw threads, plate hardware and which optics each plate takes).
Torque
per optic manual (GLOCK gives no figure)
Driver
T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Trijicon SRO on the GLOCK 17 / 19 / 45 Gen6 (ORS), Optic to plate: thread 6-32 UNC (into the slide, through the plate); torque per optic manual (GLOCK gives no figure); driver T10 / T15. Source: GLOCK, Optic Ready (OR) Plates Set sheet (01/26) (https://eu-assets.contentstack.com/v3/assets/bltf7171cc1cfc1a31f/blt9ac426e56af47ddd/69714e41d5cee4e127d4678b/OR_Adapter-Set_Gen6_012026.pdf), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/trijicon-sro-on-glock-17-19-45-gen6-ors/#joint-optic-plate

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Usually a low co-witness. A plate raises the optic, so suppressor-height irons ride near the bottom of the window: Night Fision, for one, lists its .290 in front sight as a lower 1/5 co-witness with RMR-class optics on GLOCK's MOS plate. A taller plate can drop them out of view, so check the plate's deck height before ordering sights. This optic's window runs large (25 × 22.5 mm, round with a flat bottom), which forgives a front sight slightly off the ideal height. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
How this slide mounts an opticGLOCK's Gen6 replaces MOS: the standard-frame G17, G19 and G45 come with three polymer plates (02, 03, 04), and the optic screws directly into the slide through the plate, with no metal plate in between. GLOCK's sheet gives the thread by plate and no torque, and says to use the optic maker's own screws and directions. Source: GLOCK, Gen6 optic ready page (set contents) ↗; GLOCK, announcement of the 6th Generation (2025-12-06) ↗.
About this opticThe round window makes the dot easy to pick up and is exposed to debris.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height and the ORS Plate 02. Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
GLOCK 17 / 19 / 45 Gen6 (ORS)
Optic
Trijicon SRO
Footprint
Trijicon RMR
Slide
GLOCK Gen6 ORS
Mount
Fits on the plate in the box

Parts to order

1 ×Trijicon SROTrijicon RMR footprint · 1.0 / 2.5 / 5.0 MOA$450–650
haveORS Plate 02GLOCK factory — GLOCK's sheet says Trijicon, Holosun (except the 509) and Ameriglo; its optic table names the RMR, RCR, RMR HD, SRO, Holosun 508T, 407C and 507C / Comp, and C&H Precision. One of the three plates in the Gen6 box.in the box
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic only (plate ships with the pistol)$450–650

Where to buy

Trijicon SROTrijicon RMR footprintTrijicon ↗
ORS Plate 02Ships with the pistol
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Plate → slideNone: the plate has no screws of its ownNone: GLOCK's sheet has you seat the polymer plate in the slide and fit the optic through it. It says not to reuse the cover-plate screws to hold a plate.
GLOCK's sheet gives this plate no screws: it seats on the slide and the optic goes through it. The cover-plate screws you took off are not for it.
Optic → plate6-32 UNC (into the slide, through the plate)Not in GLOCK's plate set. GLOCK's manual says to use the optic maker's own mounting screws.
GLOCK says to use the optic maker's own mounting screws and to install the optic to its maker's directions. They go through this plate and into the slide, at the thread above.

On the bench before you start

  • Torque wrench — set to the figure in your optic's manual
  • Driver bits — T10 / T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • A parts tray — you'll have three bags of look-alike screws
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Plate to slideNone: GLOCK gives no plate screws or torque
Optic torqueper optic manual (GLOCK gives no figure)
Screws6-32 UNC (into the slide, through the plate)
DriverT10 / T15
Interface2 screws, 2 forward recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the factory cover plate and set its screws aside. They are not optic screws.
  3. Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
  4. Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
  5. Torque the plate to spec, bringing the screws up evenly rather than one at a time.
  6. Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
  7. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  8. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (10)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Trijicon SRO: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The GLOCK 17 / 19 / 45 Gen6 (ORS)’s slide: screw threads, plate hardware and which optics each plate takes checked against GLOCK's OR plates set sheet (01/26) and Optic Ready System page; C&H's and Trijicon's own listings on October 1, 2026. The ORS Plate 02: screw threads, plate hardware and which optics each plate takes checked against GLOCK's OR plates set sheet (01/26) and Optic Ready System page; C&H's and Trijicon's own listings on October 1, 2026. The Gen 6 MIL/LEO → Trijicon RMR / RMR HD / SRO / RCR / Holosun 407C / 507C / 507COMP / 508T: footprints, the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026. The OPF-G6, RMR: footprints, the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.