Does the Trijicon SRO fit the Palmetto State Armory Dagger Full Size / Compact (RMR cut)?
Yes, the Trijicon SRO mounts straight to the Palmetto State Armory Dagger Full Size / Compact (RMR cut) with no adapter plate; the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Direct mount
The slide is cut for this footprint, so the optic bolts straight on.
What to buy
- Optic
- Trijicon SRO ($450–650)
- Plate
- None: it mounts straight to the slide.
- Screws
- #6-32, from the optic's or plate's box. Blue threadlocker, never red.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: co-witnesses (estimated, why).
- All in
- $450–650 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Optic → slide
- Thread
- #6-32The footprint's usual figure, but no document is linked for it here yet. What would settle it.
- Torque
- 15 in-lbThe footprint's usual figure, but no document is linked for it here yet. What would settle it.
- Driver
- T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Trijicon SRO on the Palmetto State Armory Dagger Full Size / Compact (RMR cut), Optic to slide: thread #6-32; torque 15 in-lb; driver T10 / T15. No maker document on file for the thread or torque or driver. Optic Mounting, https://opticmounting.com/fit/trijicon-sro-on-palmetto-state-armory-dagger-full-size-compact-rmr-cut/#joint-optic-slide
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
- Optic
- Trijicon SRO
- Footprint
- Trijicon RMR
- Slide
- PSA Dagger RMR cut
- Mount
- Direct mount
Parts to order
| 1 × | Trijicon SROTrijicon RMR footprint · 1.0 / 2.5 / 5.0 MOA | $450–650 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only | $450–650 |
Where to buy
| Trijicon SROTrijicon RMR footprint | Trijicon ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Optic → slide | #6-32 | Supplied with the optic. With no plate in the stack, the screws that came with the optic are normally correct. The pistol's cover-plate screws are not optic screws; set them aside. |
On the bench before you start
- Torque wrench — covering 15 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / T15, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the cover plate and set it aside with its screws.
- Degrease the slide cut and the optic base.
- Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
- Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Palmetto State Armory Dagger Full Size / Compact (RMR cut) with other optics
Every optic on the Palmetto State Armory Dagger Full Size / Compact (RMR cut), and how each mounts
The Trijicon SRO on other pistols
Plate in box8
Plate12
By serial1
Sources for this page (3)
- Slide EGW, Red Dot Sight Mount for PSA Dagger With RMR Cut (SKU 49272) ↗
- Optic Trijicon, SRO spec sheet (PML4071) ↗
- Optic Trijicon, actual-size window chart (PML5014) ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Trijicon SRO: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Palmetto State Armory Dagger Full Size / Compact (RMR cut)’s slide: EGW's listing for its PSA Dagger RMR-cut adapter (SKU 49272): URL, fit statement, optics list, hardware, torque, price checked against egwguns.com listing, read 2026-10-01 on October 1, 2026.