Does the Holosun 507C X2 fit the Palmetto State Armory Dagger Full Size / Compact (RMR cut)?

Yes, the Holosun 507C X2 mounts straight to the Palmetto State Armory Dagger Full Size / Compact (RMR cut) with no adapter plate; the optic is the only part to buy.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Direct mount

The slide is cut for this footprint, so the optic bolts straight on.

What to buy

Optic
Holosun 507C X2 ($300–450)
Plate
None: it mounts straight to the slide.
Screws
#6-32, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: co-witnesses (estimated, why).
All in
$300–450 approximate street prices, September 2026
SlidePSA Dagger RMR cut
Optic footprintTrijicon RMR
Optic screws#6-32 · T10 / T15
Optic torque15 in-lb
Cost to mount$300–450

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Optic → slide

Thread
#6-32The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Torque
15 in-lbThe footprint's usual figure, but no document is linked for it here yet. What would settle it.
Driver
T10 / T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Holosun 507C X2 on the Palmetto State Armory Dagger Full Size / Compact (RMR cut), Optic to slide: thread #6-32; torque 15 in-lb; driver T10 / T15. No maker document on file for the thread or torque or driver. Optic Mounting, https://opticmounting.com/fit/holosun-507c-x2-on-palmetto-state-armory-dagger-full-size-compact-rmr-cut/#joint-optic-slide

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Co-witnesses. A ≈0.290–0.315 in front sight normally sits in the lower third of the window on a direct cut. Mounted directly, the optic sits as low as the cut allows, the best case for a co-witness. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
How this slide mounts an opticThe RMR cut is the one EGW names as the factory cut on PSA Dagger Optics Ready slides: an RMR-pattern optic bolts straight on. EGW's adapter to the Docter footprint is made for slides with that RMR cut only, and its listing says it will not fit other slide cuts or non-optics-ready models, so check which cut your slide has before buying a plate. PSA's own pages could not be read here: which Dagger slides carry which cut, how to tell them apart, and the slide's screw thread and torque are not on file. Source: EGW, Red Dot Sight Mount for PSA Dagger With RMR Cut (SKU 49272) ↗.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Palmetto State Armory Dagger Full Size / Compact (RMR cut)
Optic
Holosun 507C X2
Footprint
Trijicon RMR
Slide
PSA Dagger RMR cut
Mount
Direct mount

Parts to order

1 ×Holosun 507C X2Trijicon RMR footprint · 2 MOA + 32 MOA circle$300–450
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic only$300–450

Where to buy

Holosun 507C X2Trijicon RMR footprintHolosun — this item ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Optic → slide#6-32Supplied with the optic.
With no plate in the stack, the screws that came with the optic are normally correct. The pistol's cover-plate screws are not optic screws; set them aside.

On the bench before you start

  • Torque wrench — covering 15 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T10 / T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Optic torque15 in-lb
Screws#6-32
DriverT10 / T15
Interface2 screws, 2 forward recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the cover plate and set it aside with its screws.
  3. Degrease the slide cut and the optic base.
  4. Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
  5. Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
  6. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  7. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (2)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Holosun 507C X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Palmetto State Armory Dagger Full Size / Compact (RMR cut)’s slide: EGW's listing for its PSA Dagger RMR-cut adapter (SKU 49272): URL, fit statement, optics list, hardware, torque, price checked against egwguns.com listing, read 2026-10-01 on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.