Does the Steiner MPS fit the GLOCK 17 / 19 / 45 Gen6 (ORS)?
Yes, the Steiner MPS fits the GLOCK 17 / 19 / 45 Gen6 (ORS) with an adapter plate: the OPF-G6, ACRO from Forward Controls Design.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Adapter plate required
Enclosed emitterThe slide isn't cut for this pattern. One plate adapts it, listed below. The plate gives the optic's clamp a rail to grip.
- OPF-G6, ACROForward Controls Design ↗$60–9517-4 stainless steel. FCD tests and supports it with the Aimpoint ACRO P-2 and Steiner MPS only. M4 × 0.7 T20 plate screws included; the optic clamps to the plate.Plate screws M4 × 0.7 · optic screws not in Forward Controls Design's listing · plate screws at 30–35 in-lb (FCD)
What to buy
- Optic
- Steiner MPS ($450–650)
- Plate
- The OPF-G6, ACRO, from Forward Controls Design ($60–95).
- Screws
- Cross-bolt clamp, from the optic's or plate's box. Blue threadlocker, never red.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: low at best (estimated, why).
- All in
- $510–745 approximate street prices, September 2026
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- M4 × 0.7From Forward Controls Design, OPF-G6, ACRO ↗, checked against it September 30, 2026 (footprints, the optics named and the included hardware).
- Torque
- 30–35 in-lb (FCD)From Forward Controls Design, OPF-G6, ACRO ↗, checked against it September 30, 2026 (footprints, the optics named and the included hardware).
Cite this joint The Steiner MPS on the GLOCK 17 / 19 / 45 Gen6 (ORS), Plate to slide: thread M4 × 0.7; torque 30–35 in-lb (FCD). Source: Forward Controls Design, OPF-G6, ACRO (https://www.forwardcontrolsdesign.com/OPF-G6-ACRO-Glock-Gen-6-ACRO-plate_p_685.html), checked 2026-09-30. Optic Mounting, https://opticmounting.com/fit/steiner-mps-on-glock-17-19-45-gen6-ors/#joint-plate-slide
Optic → interface
- Thread
- Cross-bolt clamp
- Torque
- per Aimpoint manual
- Driver
- T10 / hex per modelThe footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Steiner MPS on the GLOCK 17 / 19 / 45 Gen6 (ORS), Optic to interface: thread Cross-bolt clamp; torque per Aimpoint manual; driver T10 / hex per model. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/steiner-mps-on-glock-17-19-45-gen6-ors/#joint-optic-interface
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Optic
- Steiner MPS
- Footprint
- Aimpoint ACRO
- Slide
- GLOCK Gen6 ORS
- Mount
- Adapter plate required
Parts to order
| 1 × | Steiner MPSAimpoint ACRO footprint · 3.3 MOA | $450–650 |
| 1 × | OPF-G6, ACROForward Controls Design — 17-4 stainless steel. FCD tests and supports it with the Aimpoint ACRO P-2 and Steiner MPS only. M4 × 0.7 T20 plate screws included; the optic clamps to the plate. | $60–95 |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic + plate | $510–745 |
Where to buy
| Steiner MPSAimpoint ACRO footprint | Steiner ↗ |
| OPF-G6, ACROForward Controls Design | Forward Controls Design — this item ↗ |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | M4 × 0.7 | Supplied with the plate. The one screwed joint in this stack, so it gets the threadlocker and the torque check. Keep the pistol's cover-plate screws apart from these. |
| Optic → interface | Cross-bolt clamp | Supplied with the optic. The ACRO clamps rather than bolting through, so there's no screw length to get wrong. Torque the cross-bolt to Aimpoint's figure. |
On the bench before you start
- Torque wrench — covering 35 in-lb (a 10–50 in-lb driver covers most jobs)
- Driver bits — T10 / hex per model, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Set the optic on the plate's rail and tighten its cross-bolt clamp to Aimpoint's figure. There are no optic screws to fit.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The GLOCK 17 / 19 / 45 Gen6 (ORS) with other optics
Every optic on the GLOCK 17 / 19 / 45 Gen6 (ORS), and how each mounts
The Steiner MPS on other pistols
Plate15
- GLOCK 19 Gen5 MOS
- Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in)
- SIG Sauer P320 X-Carry
- GLOCK 17 Gen5 MOS
- Springfield Armory Echelon
- GLOCK 45 Gen5 MOS
- GLOCK 26 Gen5 MOS
- Canik METE SFx
- SIG Sauer P320 XCompact
- Smith & Wesson M&P9 M2.0 Compact Optics Ready
- CZ P-10 C Optics Ready
- Heckler & Koch VP9 Optics Ready
- Staccato P
- CZ Shadow 2 Optics Ready
- Canik TTI Combat
No fit15
- SIG Sauer P365XL
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- GLOCK 48 MOS
- Walther PDP Full Size (1.0)
- Shadow Systems MR920
- Ruger RXM
- SIG Sauer P365X
- SIG Sauer P365 Optics Ready
- SIG Sauer P365-XMACRO / XMACRO Comp
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Walther PDP Compact (1.0)
- Taurus GX4 TORO / GX4XL
- Palmetto State Armory Dagger Full Size / Compact (RMR cut)
Sources for this page (7)
- Slide GLOCK, Optic Ready (OR) Plates Set sheet (01/26) ↗
- Slide GLOCK, Optic Ready System page (Gen6 optic table) ↗
- Slide GLOCK, instructions for use, Gen6 (10-25) ↗
- Slide GLOCK, Gen6 optic ready page (set contents) ↗
- Slide GLOCK, announcement of the 6th Generation (2025-12-06) ↗
- Optic Steiner, MPS ↗
- Plate Forward Controls Design, OPF-G6, ACRO ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Steiner MPS: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The GLOCK 17 / 19 / 45 Gen6 (ORS)’s slide: screw threads, plate hardware and which optics each plate takes checked against GLOCK's OR plates set sheet (01/26) and Optic Ready System page; C&H's and Trijicon's own listings on October 1, 2026. The OPF-G6, ACRO: footprints, the optics named and the included hardware checked against the plate maker's own listing on September 30, 2026.