Home / Pistols / SIG Sauer P320 X-Carry / Leupold DeltaPoint Pro

Does the Leupold DeltaPoint Pro fit the SIG Sauer P320 X-Carry?

Yes, the Leupold DeltaPoint Pro mounts straight to the SIG Sauer P320 X-Carry with no adapter plate; the optic is the only part to buy.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Direct mount — cross-compatible

The slide is cut for SIG Romeo1Pro, and this footprint fits that cut with no adapter.

What to buy

Optic
Leupold DeltaPoint Pro ($300–450)
Plate
None: it mounts straight to the slide.
Screws
M4 × 0.7, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: co-witnesses (estimated, why).
All in
$300–450 approximate street prices, September 2026
Same answer forThe Leupold DeltaPoint Pro goes on the SIG Sauer P320 XCompact, SIG Sauer P320 XFive Legion, SIG Sauer P320 XTen, SIG Sauer P320 AXG Legion / AXG Pro, SIG Sauer P320 Spectre Comp and SIG Sauer P320-M17 / M18 the same way: they share this slide's optic cut.
SlideSIG P320 optic cut (Romeo1Pro pattern)
Optic footprintLeupold DeltaPoint Pro
Optic screwsM4 × 0.7 · T15
Optic torque20 in-lb (confirm current Leupold spec)
Cost to mount$300–450

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Optic → slide

Thread
M4 × 0.7From SIG Sauer, ROMEO1PRO operator's manual (REV05) ↗; SIG Sauer, ROMEO2 operator's manual (REV04) ↗, checked against them September 30, 2026 (slide screw thread; footprint screw, torque and driver).
Torque
20 in-lb (confirm current Leupold spec)The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Driver
T15The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Leupold DeltaPoint Pro on the SIG Sauer P320 X-Carry, Optic to slide: thread M4 × 0.7; torque 20 in-lb (confirm current Leupold spec); driver T15. Source: SIG Sauer, ROMEO1PRO operator's manual (REV05) (https://www.sigsauer.com/media/sigsauer/resources/OPERATORS_MANUAL_ROMEO1PRO_7401786-01_REV05_WEB_FILE.pdf), checked 2026-09-30; SIG Sauer, ROMEO2 operator's manual (REV04) (https://www.sigsauer.com/media/sigsauer/resources/operators_manual-romeo2-7402277-01-rev04-lr.pdf), checked 2026-09-30. No maker document on file for the torque or driver. Optic Mounting, https://opticmounting.com/fit/leupold-deltapoint-pro-on-sig-sauer-p320-x-carry/#joint-optic-slide

Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Co-witnesses. A ≈0.290–0.315 in front sight normally sits in the lower third of the window on a direct cut. Mounted directly, the optic sits as low as the cut allows, the best case for a co-witness. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
How this slide mounts an opticOptic-ready P320 slides are milled for SIG's own Romeo1Pro pattern, which also takes DeltaPoint Pro-footprint optics: SIG sells its DPP-footprint ROMEO-X PRO for the optic-ready P320. Everything else goes on through a plate, and there are plenty to choose from.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
SIG Sauer P320 X-Carry
Optic
Leupold DeltaPoint Pro
Footprint
Leupold DeltaPoint Pro
Slide
SIG P320 optic cut (Romeo1Pro pattern)
Mount
Direct mount — cross-compatible

Parts to order

1 ×Leupold DeltaPoint ProLeupold DeltaPoint Pro footprint · 2.5 / 6 MOA or 7.5 MOA delta$300–450
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic only$300–450

Where to buy

Leupold DeltaPoint ProLeupold DeltaPoint Pro footprintLeupold ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Optic → slideM4 × 0.7Supplied with the optic.
With no plate in the stack, the screws that came with the optic are normally correct. The pistol's cover-plate screws are not optic screws; set them aside.

On the bench before you start

  • Torque wrench — covering 20 in-lb (a 10–50 in-lb driver covers most jobs)
  • Driver bits — T15, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Optic torque20 in-lb (confirm current Leupold spec)
ScrewsM4 × 0.7
DriverT15
Interface2 screws, 4 corner recoil lugs

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the cover plate and set it aside with its screws.
  3. Degrease the slide cut and the optic base.
  4. Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
  5. Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
  6. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  7. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (3)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Leupold DeltaPoint Pro: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The SIG Sauer P320 X-Carry’s slide: slide screw thread; footprint screw, torque and driver checked against SIG's ROMEO1PRO (REV05) and ROMEO2 (REV04) operator's manuals on September 30, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.