Does the Holosun 407K X2 fit the Smith & Wesson M&P9 M2.0 Compact Optics Ready?
Yes, the Holosun 407K X2 fits the Smith & Wesson M&P9 M2.0 Compact Optics Ready on a plate that ships with the pistol (C.O.R.E. Plate 2 (Shield / RMSc family)); the optic is the only part to buy.
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
Fits on the plate in the box
The C.O.R.E. Plate 2 (Shield / RMSc family) that ships with the pistol adapts the slide to this footprint. Aftermarket plates are listed below too.
- C.O.R.E. Plate 2 (Shield / RMSc family)S&W factory ↗in the boxpriced here and used on the build sheetS&W's guide: Shield RMS / RMSc / RMS2, SIG ROMEOZero, Vortex Defender-CCW, Crimson Trace CTS-1550, and the Holosun 407K / 507K and EPS Carry.
What to buy
- Optic
- Holosun 407K X2 ($150–300)
- Plate
- None to buy: the C.O.R.E. Plate 2 (Shield / RMSc family) ships with the pistol. Look in the box.
- Screws
- Look in the pistol's box with the plates; if there are none, buy a pair made for this plate.
- Iron sights
- Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: usually a low co-witness (estimated, why).
- All in
- $150–300 approximate street prices, September 2026
Three other plates fit
- M&P 2.0 → Holosun KC&H Precision ↗$25–60407K / 507K — mounts lower than stacking a K-to-RMR interface adapter
- M&P 2.0 → EPS / EPS Carry / SCS CarryC&H Precision ↗$25–60Plate screws not in C&H Precision's listing · optic screws #6-32
- Steel plates — MPS / RMR / KAthena Precision ↗$60–95Steel rather than aluminium; worth it on a comped gun
New to red dots? What footprint, plate, co-witness and the rest mean
Screws and torque, joint by joint
Each figure with the document it comes from and the date it was last checked against it, for the C.O.R.E. Plate 2 (Shield / RMSc family). Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.
Plate → slide
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate instructions
Cite this joint The Holosun 407K X2 on the Smith & Wesson M&P9 M2.0 Compact Optics Ready, Plate to slide: thread not on file; torque per plate instructions. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-smith-and-wesson-m-and-p9-m2-0-compact-optics-ready/#joint-plate-slide
Optic → plate
- Thread
- per plate maker, not on file hereNot on file. What would settle it.
- Torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)Not on file. What would settle it.
- Driver
- T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.
Cite this joint The Holosun 407K X2 on the Smith & Wesson M&P9 M2.0 Compact Optics Ready, Optic to plate: thread not on file; torque not on file; driver T10. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-smith-and-wesson-m-and-p9-m2-0-compact-optics-ready/#joint-optic-plate
What to order, and how to fit it
The fit checker's build sheet for this pair, assuming sights of unknown height and the C.O.R.E. Plate 2 (Shield / RMSc family). Open it in the fit checker to set your sights, pick another plate, work out screw length from your own caliper readings, or copy it as text.
Print this sheet for your gunsmith. Installation guide.
Build sheet
- Pistol
- Smith & Wesson M&P9 M2.0 Compact Optics Ready
- Optic
- Holosun 407K X2
- Footprint
- Holosun K
- Slide
- S&W M&P C.O.R.E. / Optics Ready
- Mount
- Fits on the plate in the box
Parts to order
| 1 × | Holosun 407K X2Holosun K footprint · 6 MOA | $150–300 |
| have | C.O.R.E. Plate 2 (Shield / RMSc family)S&W factory — S&W's guide: Shield RMS / RMSc / RMS2, SIG ROMEOZero, Vortex Defender-CCW, Crimson Trace CTS-1550, and the Holosun 407K / 507K and EPS Carry. | in the box |
| 1 set | Suppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one. | optional |
| Estimated total: optic only (plate ships with the pistol) | $150–300 |
Where to buy
| Holosun 407K X2Holosun K footprint | Holosun ↗ |
| C.O.R.E. Plate 2 (Shield / RMSc family) | Ships with the pistol |
| Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson |
Fasteners: which bag
You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.
| Joint | Thread | Comes from |
|---|---|---|
| Plate → slide | per plate maker, not on file here | Supplied with the plate. Two kinds of short screw come with the pistol: these, for the plate, and the pair already holding the cover plate on the slide. They are different lengths, so keep them apart. |
| Optic → plate | per plate maker, not on file here | Look in the pistol's box, with the plates. If there are none, buy a pair made for this plate. Most mistakes happen here. The screws in the optic's box are cut for mounting straight onto a slide; a plate changes the stack, so the plate maker supplies the right pair. If your plate came without screws, measure before you buy. |
On the bench before you start
- Torque wrench — set to the figure in your optic's manual
- Driver bits — T10, fully seated so they don't round the head
- Calipers — for the screw length check below
- Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
- Degreaser — isopropyl or brake cleaner
- A parts tray — you'll have three bags of look-alike screws
- Witness-mark paint or lacquer — so you can see if anything moves later
Install spec
Not on file for this build
Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.
- Plate → slide thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Optic → plate thread
- Not published where this site could find it. Ask the plate maker, or check the screw bag's label.
- Optic screw torque
- Not published for this plate. Use the plate maker's figure, not the optic maker's, which is for a slide.
- Screw length
- Never published here, because it depends on your exact stack. Measure it and test-fit dry.
Sequence
- Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
- Remove the factory cover plate and set its screws aside. They are not optic screws.
- Degrease the slide pocket, both faces of the plate and the optic base. Oil under a plate lets it move.
- Seat the plate on the slide, check it sits flat with no rock, and fit its screws with blue threadlocker.
- Torque the plate to spec, bringing the screws up evenly rather than one at a time.
- Seat the optic on the plate's recoil posts, fit the optic screws with blue threadlocker, and torque to the optic spec.
- Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
- Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.
Before you fire it
- Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
- Optic sits flat with no rock, and the screws pulled up evenly.
- Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
- Threadlocker cured.
- Function check, then zero confirmed live.
Screw length is the one that hurts
Shop log (fill in)
| Torque wrench, and setting | |
| Plate screws: thread, length, torque | |
| Optic screws: thread, length, torque | |
| Threadlocker used (product, or none) | |
| Witness marks applied | |
| Zeroed at (distance, ammunition) | |
| Torque re-checked after (rounds) | |
| Fitted by, and date |
Sight co-witness
The Smith & Wesson M&P9 M2.0 Compact Optics Ready with other optics
Plate in box9
No fit1
Every optic on the Smith & Wesson M&P9 M2.0 Compact Optics Ready, and how each mounts
The Holosun 407K X2 on other pistols
Direct (cross-fit)7
Plate20
- GLOCK 19 Gen5 MOS
- GLOCK 43X MOS
- Springfield Armory Hellcat OSP
- SIG Sauer P320 X-Carry
- GLOCK 17 Gen5 MOS
- GLOCK 48 MOS
- Walther PDP Full Size (1.0)
- Ruger RXM
- GLOCK 45 Gen5 MOS
- GLOCK 26 Gen5 MOS
- Smith & Wesson M&P Shield Plus Optics Ready
- Springfield Armory Hellcat Pro
- Canik METE SFx
- SIG Sauer P320 XCompact
- GLOCK 17 / 19 / 45 Gen6 (ORS)
- Walther PDP Compact (1.0)
- CZ P-10 C Optics Ready
- Heckler & Koch VP9 Optics Ready
- CZ Shadow 2 Optics Ready
- Canik TTI Combat
Sources for this page (6)
- Slide Smith & Wesson, optic fitment guide: M&P M2.0 with C.O.R.E. plates (2025, v5) ↗
- Slide Smith & Wesson, M&P9 M2.0 Optics Ready Full Size product page ("Seven mounting plates included") ↗
- Optic Holosun, HS407K-X2 (in the box: 2× M4×12, 2× #6-32×7.4) ↗
- Plate C&H Precision, M&P 2.0 → Holosun K ↗
- Plate C&H Precision, M&P 2.0 → EPS / EPS Carry / SCS Carry ↗
- Plate Athena Precision, Steel plates — MPS / RMR / K ↗
Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.
Last checked against the makers’ documents. The Holosun 407K X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Smith & Wesson M&P9 M2.0 Compact Optics Ready’s slide: the plate for each optic, and the plates in the box checked against S&W's M&P M2.0 optic fitment guide (2025, v5) and product page on September 30, 2026. The C.O.R.E. Plate 2 (Shield / RMSc family): the plate for each optic, and the plates in the box checked against S&W's M&P M2.0 optic fitment guide (2025, v5) and product page on September 30, 2026. The M&P 2.0 → EPS / EPS Carry / SCS Carry: screw threads checked against the plate maker's own hardware list on September 28, 2026. Not individually re-checked since it was compiled (September 2026): 2 plates.