Home / Pistols / Taurus GX4 TORO / GX4XL / Holosun 407K X2

Does the Holosun 407K X2 fit the Taurus GX4 TORO / GX4XL?

Yes, the Holosun 407K X2 mounts straight to the Taurus GX4 TORO / GX4XL with no adapter plate; the optic is the only part to buy.

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

Direct mount — cross-compatible

The slide is cut for Shield RMSc, and this footprint fits that cut with no adapter.

What to buy

Optic
Holosun 407K X2 ($150–300)
Plate
None: it mounts straight to the slide.
Screws
M4 × 0.7, from the optic's or plate's box. Blue threadlocker, never red.
Iron sights
Standard-height irons: no co-witness, typically (not a rule). Suppressor-height irons: co-witnesses (estimated, why).
All in
$150–300 approximate street prices, September 2026
Same answer forThe Holosun 407K X2 goes on the Taurus GX4 Carry TORO and Taurus GX4 Graphene TORO the same way: they share this slide's optic cut.
SlideTaurus GX4 T.O.R.O. direct cut
Optic footprintHolosun K
Optic screwsM4 × 0.7 · T10
Optic torque8.2 in-lb
Cost to mount$150–300

Screws and torque, joint by joint

Each figure with the document it comes from and the date it was last checked against it. Where there is no document, it says so. Each joint has its own link, and a line to cite it by: one click selects the whole line.

Optic → slide

Thread
M4 × 0.7From Taurus, GX4 instruction manual (a distributor-hosted copy of Taurus's file, PDF created 2021-09), T.O.R.O. configuration pp. 28-31 ↗, checked against it October 1, 2026 (Taurus GX4 T.O.R.O. cut: footprint, direct list, thread, torque, the RMRcc adapter plate, what ships in the box).
Torque
8.2 in-lbFrom Taurus, GX4 instruction manual (a distributor-hosted copy of Taurus's file, PDF created 2021-09), T.O.R.O. configuration pp. 28-31 ↗, checked against it October 1, 2026 (Taurus GX4 T.O.R.O. cut: footprint, direct list, thread, torque, the RMRcc adapter plate, what ships in the box).
Driver
T10The footprint's usual figure, but no document is linked for it here yet. What would settle it.

Cite this joint The Holosun 407K X2 on the Taurus GX4 TORO / GX4XL, Optic to slide: thread M4 × 0.7; torque 8.2 in-lb; driver T10. Source: Taurus, GX4 instruction manual (a distributor-hosted copy of Taurus's file, PDF created 2021-09), T.O.R.O. configuration pp. 28-31 (https://s3.amazonaws.com/files.ammunitiondepot.com/taurus-firearms/pistols/taurus-gx4-pistol-instruction-manual.pdf), checked 2026-10-01. No maker document on file for the driver. Optic Mounting, https://opticmounting.com/fit/holosun-407k-x2-on-taurus-gx4-toro-gx4xl/#joint-optic-slide

Which screwsTaurus's manual says to use the optic's own screws only if they are M4 × 0.7 mm, with at least 4 threads of engagement in the slide; otherwise use the two screws that came with the slide cover. The Holosun 407K X2 box holds M4 and #6-32 screws. Use the M4 pair; the other won't thread in. Source: Taurus, GX4 instruction manual (a distributor-hosted copy of Taurus's file, PDF created 2021-09), T.O.R.O. configuration pp. 28-31 ↗; Holosun, HS407K-X2 (in the box: 2× M4×12, 2× #6-32×7.4) ↗.
Will your iron sights co-witness?With standard-height irons: No co-witness. Standard-height irons sit well below any pistol red dot window and are only usable with the optic off. Suppressor-height sights fix that; a different optic won't. Little or no data: no sight maker publishes co-witness heights for standard-height irons with this pair, so "no co-witness" is the typical case, not a rule. Some optics still show factory-height irons in the lower third or lower fifth of the window, so check your own front sight against the window before you rely on it.With suppressor-height irons: Co-witnesses. A ≈0.290–0.315 in front sight normally sits in the lower third of the window on a direct cut. Mounted directly, the optic sits as low as the cut allows, the best case for a co-witness. This optic's window runs small (19.6 × 14.7 mm), so a front sight slightly off the ideal height is more likely to miss it. Estimated: no sight maker publishes heights for this pair, so that's the typical case for this kind of optic, not a guarantee: pistols don't standardize sight and optic heights the way rifles do.
How this slide mounts an opticMilled for the Shield RMSc pattern, so Shield RMSc and Holosun K optics bolt straight on. Taurus's manual and its parts store list the Riton 3 Tactix MPRD 2, Sightmark Mini Shot A-Spec M3, Shield RMSc, Holosun 407K / 507K, SIG RomeoZero and HEX Wasp for the cut, and the Trijicon RMRcc only with an adapter plate that Taurus sells separately (it says the RMRcc will not work on the GX4 T.O.R.O. without it). The pistol ships with a flush slide cover over the cut, not a plate; the optic and the adapter plate are not included. Taurus gives 8.2 in-lbs for the two screws that hold an optic, with Loctite 242 and a 24-hour cure. It gives no torque for the adapter plate's own screws. Source: ShopTaurus, Taurus GX4 T.O.R.O. Conversion Kit (footprint list; the Trijicon RMRcc adapter plate is sold separately) ↗; ShopTaurus, Taurus GX4/GX4XL/GX4 Carry TORO Slide Cover Screws ↗.

What to order, and how to fit it

The fit checker's build sheet for this pair, assuming sights of unknown height. Open it in the fit checker to set your sights, work out screw length from your own caliper readings, or copy it as text.

Print this sheet for your gunsmith. Installation guide.

Build sheet

Data compiled September 2026 · Optic Mounting
Pistol
Taurus GX4 TORO / GX4XL
Optic
Holosun 407K X2
Footprint
Holosun K
Slide
Taurus GX4 T.O.R.O. direct cut
Mount
Direct mount — cross-compatible

Parts to order

1 ×Holosun 407K X2Holosun K footprint · 6 MOA$150–300
1 setSuppressor-height sights, if yours are standardMeasure your front sight first, then compare it with the sight heights published for this slide and optic, where the sheet lists them. The height that co-witnesses depends on the slide and the optic; a slim slide needs less than a full-size one.optional
Estimated total: optic only$150–300

Where to buy

Holosun 407K X2Holosun K footprintHolosun ↗
Suppressor-height sights, if yours are standardOptional, for a co-witness. Makers include Trijicon, Ameriglo, XS and Dawson

Fasteners: which bag

You don't buy these. Screws come with the pistol, the optic and the plate, and they look alike. The thread is tapped into the slide or plate (the optic only has a clearance hole), so they decide the thread, not the optic.

JointThreadComes from
Optic → slideM4 × 0.7Supplied with the optic: the M4 pair.
The slide's tapping decides the screw, not the optic. Start each screw by hand.Thread trapTaurus's manual says to use the optic's own screws only if they are M4 × 0.7 mm, with at least 4 threads of engagement in the slide; otherwise use the two screws that came with the slide cover. The Holosun 407K X2 box holds M4 and #6-32 screws. Use the M4 pair; the other won't thread in.

On the bench before you start

  • Torque wrench — covering 8.2 in-lb (below the range of many torque drivers: check yours reaches it)
  • Driver bits — T10, fully seated so they don't round the head
  • Calipers — for the screw length check below
  • Blue removable threadlocker — Vibra-Tite VC-3 or Loctite 242. Never red.
  • Degreaser — isopropyl or brake cleaner
  • Witness-mark paint or lacquer — so you can see if anything moves later

Install spec

Optic torque8.2 in-lb
ScrewsM4 × 0.7
DriverT10
Interface2 screws, 2 forward lugs (rear posts omitted)

Not on file for this build

Where a figure is not published, this sheet says so instead of guessing. Get these from the maker or your gunsmith.

Screw length
Never published here, because it depends on your exact stack. Measure it and test-fit dry.

Sequence

  1. Clear the pistol. Drop the magazine, lock the slide back, look and feel the chamber, then do it again.
  2. Remove the cover plate and set it aside with its screws.
  3. Degrease the slide cut and the optic base.
  4. Seat the optic on the slide's recoil lugs and check it sits flat with no rock.
  5. Fit the optic screws with blue threadlocker and torque to spec, alternating between them.
  6. Let the threadlocker cure before firing (check the bottle; usually a few hours to overnight).
  7. Confirm zero at your working distance, then re-check torque after the first 100–200 rounds.

Before you fire it

  • Screw length checked dry: it must not bottom out on the slide or reach the striker channel.
  • Optic sits flat with no rock, and the screws pulled up evenly.
  • Torque set with a wrench, not by feel. Witness-mark the screws so movement is visible later.
  • Threadlocker cured.
  • Function check, then zero confirmed live.

Screw length is the one that hurts

Too long and a screw bottoms out on the slide or reaches the striker channel; too short and it strips under recoil. This sheet gives the thread but can't give the length, which depends on your exact plate and optic stack. Test-fit dry and count threads.

Shop log (fill in)

Torque wrench, and setting 
Plate screws: thread, length, torque 
Optic screws: thread, length, torque 
Threadlocker used (product, or none) 
Witness marks applied 
Zeroed at (distance, ammunition) 
Torque re-checked after (rounds) 
Fitted by, and date 

Sight co-witness

Confirm the firearm is unloaded before any work on the slide. Mounting an optic is gunsmithing: stay within your competence and use a gunsmith when a job is past it. Provided as-is with no warranty; you use this at your own risk. Prices are approximate street-price bands from September 2026. Torque and fitment figures come from manufacturer documentation; confirm against the current manuals for your pistol, optic and plate before installing. Not affiliated with or endorsed by any manufacturer.
Sources for this page (5)

Data compiled September 2026 from these documents. A figure with no source here is marked "not on file" on the page. How the data is checked.

Last checked against the makers’ documents. The Holosun 407K X2: window, weight and dot checked against the maker's own spec sheet or manual on September 26, 2026. The Taurus GX4 TORO / GX4XL’s slide: Taurus GX4 T.O.R.O. cut: footprint, direct list, thread, torque, the RMRcc adapter plate, what ships in the box checked against Taurus GX4 instruction manual, T.O.R.O. configuration pp. 28-31 (distributor-hosted copy of Taurus's file); ShopTaurus (Taurus's own store): Trijicon RMRcc adapter plate listing, T.O.R.O. conversion kit and slide kit pages, T.O.R.O. cover screw and adapter pin listings on October 1, 2026.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.