Moving the C-More STS2 between pistols
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
You already own it. Here is what changes from one slide to the next: the plate, the screw thread at each joint, the torque, the tools and any thread trap. 15 kinds of slide, covering 52 pistols, grouped by how the optic mounts and then alphabetically. Nothing is ranked. The C-More STS2 page has its specs and the per-pair answers.
13 of the 15 blocks have a figure marked not on file: no maker publishes it where this site could find it, so the plate maker or a gunsmith is the source. How the data is checked.
Mounts on a plate
Arex Zero 1 Tactical ROR plate system
Plate Adapter plate required
Slide: Arex Zero 1 Tactical
- Plate
- Zero 1 Tactical ROR plate — C-MoreAftermarket
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Beretta 92X / M9A4 plate system
Plate Adapter plate required
7 slides: Beretta 92X RDO, Beretta 92X / 92XI / 92XI SAO, Beretta 92XI Squalo, Beretta 92 GTS, Beretta M9A4, Beretta 92FS X Performance OR, Beretta 94X Performance
- Plate
- 92X / M9A4 → C-More RTSBeretta factory; 1 other plate on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Canik SFx Rival optic interface plates
Plate Adapter plate required
Slide: Canik SFx Rival / Rival-S
- Plate
- Canik interface R03 → C-More STS-2Canik factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
Canik TP9 SFx optic interface plates
Plate Adapter plate required
Slide: Canik TP9 SFx
- Plate
- Canik interface 03 → C-More STS-2Canik factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
CZ P-10 OR plate system
Plate Adapter plate required
3 slides: CZ P-10 C Optics Ready, CZ P-10 F Optics Ready, CZ P-10 S Optics Ready
- Plate
- P-10 OR → C-More RTSCZ factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- 1.3 Nm (11.5 in-lb)
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $360–545approximate street prices, September 2026
CZ Shadow 2 OR plate system
Plate Adapter plate required
2 slides: CZ Shadow 2 Optics Ready, CZ Shadow 2 Compact Optics Ready
- Plate
- Shadow 2 OR → C-More RTSCZ factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $360–545approximate street prices, September 2026
GLOCK Gen6 ORS
Plate Fits on the plate in the box
Slide: GLOCK 17 / 19 / 45 Gen6 (ORS)
- Plate
- ORS Plate 03GLOCK factory, ships with the pistol
- Plate → slide
- None: the plate has no screws of its ownNone: GLOCK's sheet has you seat the polymer plate in the slide and fit the optic through it. It says not to reuse the cover-plate screws to hold a plate.
- Optic → plate
- 8-32 UNC (into the slide, through the plate)Not in GLOCK's plate set. GLOCK's manual says to use the optic maker's own mounting screws.
- Plate torque
- None: GLOCK gives no plate screws or torque
- Optic torque
- per optic manual (GLOCK gives no figure)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
GLOCK MOS — 10 mm / .45 frames
Plate Adapter plate required
4 slides: GLOCK 20 Gen5 MOS (10 mm), GLOCK 21 Gen5 MOS (.45), GLOCK 40 MOS (10 mm), GLOCK 41 MOS (.45)
- Plate
- MOS Plate 07GLOCK factory
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- 8-32 UNCNot in GLOCK's plate set, which holds the plate screws only. GLOCK says to fit the optic as its maker directs, with screws that do not come through the 2.5 mm plate.
- Plate torque
- 13.1 in-lb (1.5 Nm)
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
GLOCK MOS — standard & full size
Plate Adapter plate required
12 slides: GLOCK 19 Gen5 MOS, GLOCK 17 Gen5 MOS, GLOCK 45 Gen5 MOS, GLOCK 47 Gen5 MOS, GLOCK 49 Gen5 MOS, GLOCK 19X MOS, GLOCK 34 Gen5 MOS, GLOCK 26 Gen5 MOS, GLOCK 17 / 19 / 34 Gen4 MOS, GLOCK 22 / 23 Gen5 MOS (.40), GLOCK 35 Gen5 MOS (.40), GLOCK 44 MOS (.22 LR)
- Plate
- MOS Plate 03GLOCK factory; 1 other plate on the pair pages
- Plate → slide
- M3Supplied with the pistol, in the box with the cover plate.
- Optic → plate
- 8-32 UNCNot in GLOCK's plate set, which holds the plate screws only. GLOCK says to fit the optic as its maker directs, with screws that do not come through the 2.5 mm plate.
- Plate torque
- 13.1 in-lb (1.5 Nm)
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
HK VP9 / SFP9 OR plate system
Plate Adapter plate required
4 slides: Heckler & Koch VP9 Optics Ready, Heckler & Koch VP9 Match OR, Heckler & Koch VP9SK Optics Ready, Heckler & Koch SFP9 OR (European VP9)
- Plate
- HK Optics Plate #3 (50254263)HK factory
- Plate → slide
- M4The two screws that hold the cover plate on the slide, reused for the plate (HK sells spares, part 50947116, and says to replace them after 2,000 rounds).
- Optic → plate
- per plate maker, not on file hereNot stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying.
- Plate torque
- 2 Nm (17.7 in-lb, converted)
- Optic torque
- per the optic maker (HK's manual gives no figure)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Rear-sight dovetail mount
Plate Dovetail mount required
2 slides: CZ P-07 / P-09 (standard, no optic cut), CZ 75 / SP-01 / Shadow 2 (non-OR)
- Plate
- Dovetail mount → RMR / C-More / Docter (type C)EGW
- Mount → dovetail
- set by the slideSupplied with the mount.
- Optic → mount
- per C-More kitSupplied with the plate, not the optic.
- Plate torque
- per mount instructions
- Optic torque
- per C-More manual
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Brass drift or sight pusher, Witness-mark paint or lacquer
- To mount
- $335–535approximate street prices, September 2026
S&W M&P C.O.R.E. / Optics Ready
Plate Fits on the plate in the box
8 slides: Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Smith & Wesson M&P9 M2.0 Compact Optics Ready, Smith & Wesson M&P9 M2.0 Metal, Smith & Wesson Performance Center M&P9 M2.0 Metal / Spec Series, Smith & Wesson M&P10mm M2.0 Optics Ready, Smith & Wesson M&P9 C.O.R.E. (pre-M2.0), Smith & Wesson M&P Carry Comp, Smith & Wesson M&P Competitor
- Plate
- C.O.R.E. Plate 4 (C-More)S&W factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
Taurus T.O.R.O. plate system
Plate Verify Adapter plate required
2 slides: Taurus G3 TORO / G3X TORO, Taurus G3C TORO / G3X TORO
- Plate
- T.O.R.O. Plate #3Taurus factory; 1 other plate on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
Walther PDP 2.0 optic cut
Plate Adapter plate required
2 slides: Walther PDP 2.0 Full Size, Walther PDP 2.0 Compact
- Plate
- PDP 2.0 → C-More RTSOptics Spot
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Walther Q4 SF / Q5 Match SF optic cut
Plate Adapter plate required
2 slides: Walther Q5 Match SF, Walther Q4 SF Optics Ready
- Plate
- Universal type EOptics Spot
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Steps and safety: installing a red dot, from the makers' manuals. Mounting an optic is gunsmithing; confirm the pistol is unloaded first. Screw length is never listed here because it depends on the whole stack: each pair's build sheet has a calculator that works from your own caliper readings.