Moving the Noblex Sight III / Docter Sight C between pistols
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
You already own it. Here is what changes from one slide to the next: the plate, the screw thread at each joint, the torque, the tools and any thread trap. 21 kinds of slide, covering 76 pistols, grouped by how the optic mounts and then alphabetically. Nothing is ranked. The Noblex Sight III / Docter Sight C page has its specs and the per-pair answers.
19 of the 21 blocks have a figure marked not on file: no maker publishes it where this site could find it, so the plate maker or a gunsmith is the source. How the data is checked.
Mounts straight to the slide
Shadow Systems multi-optic cut (MR920, DR920, XR920)
Direct (cross-fit) Direct mount — cross-compatible
5 slides: Shadow Systems MR920, Shadow Systems DR920 / DR920P, Shadow Systems XR920 / XR920P, Shadow Systems Foundation Series, Shadow Systems MR920 Elite / Combat
- Optic → slide
- Not on file: Shadow Systems supplies the screws in its optic kitShadow's optic kit, taped inside the pistol box lid. This optic is not in Shadow's optic-fit table: try the kit's screws until a set goes through the optic and tightens against its body without bottoming out.
- Optic torque
- 10–20 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
Mounts on a plate
Arex Delta Gen.2 plate system
Plate Adapter plate required
Slide: Arex Delta Gen.2
- Plate
- Delta Gen.2 optic plate — type 1Aftermarket
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Arex Zero 1 Tactical ROR plate system
Plate Adapter plate required
Slide: Arex Zero 1 Tactical
- Plate
- Zero 1 Tactical ROR plate — Docter / Insight / Meopta / VortexAftermarket
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Beretta 92X / M9A4 plate system
Plate Adapter plate required
7 slides: Beretta 92X RDO, Beretta 92X / 92XI / 92XI SAO, Beretta 92XI Squalo, Beretta 92 GTS, Beretta M9A4, Beretta 92FS X Performance OR, Beretta 94X Performance
- Plate
- 92X / M9A4 → Docter / VenomBeretta factory; 1 other plate on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Beretta APX A1 / APX RDO plate system
Plate Adapter plate required
3 slides: Beretta APX A1 Full Size, Beretta APX A1 Compact, Beretta APX RDO
- Plate
- Universal type FOptics Spot
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Canik SFx Rival optic interface plates
Plate Fits on the plate in the box
Slide: Canik SFx Rival / Rival-S
- Plate
- Canik interface R01 → DocterCanik factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
Canik TP9 SFx optic interface plates
Plate Fits on the plate in the box
Slide: Canik TP9 SFx
- Plate
- Canik interface 01 → DocterCanik factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
CZ P-10 OR plate system
Plate Adapter plate required
3 slides: CZ P-10 C Optics Ready, CZ P-10 F Optics Ready, CZ P-10 S Optics Ready
- Plate
- P-10 OR → DocterCZ factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- 1.3 Nm (11.5 in-lb)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $360–545approximate street prices, September 2026
CZ Shadow 2 OR plate system
Plate Adapter plate required
2 slides: CZ Shadow 2 Optics Ready, CZ Shadow 2 Compact Optics Ready
- Plate
- Shadow 2 OR → DocterCZ factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $360–545approximate street prices, September 2026
FN MRD plate system
Plate Fits on the plate in the box
5 slides: FN 509 MRD / Tactical, FN 509 Midsize MRD / Compact MRD, FN 509 LS Edge, FN 510 / 545 MRD, FN 509 CC Edge
- Plate
- FN MRD → DocterFN factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
GLOCK MOS — 10 mm / .45 frames
Plate Adapter plate required
4 slides: GLOCK 20 Gen5 MOS (10 mm), GLOCK 21 Gen5 MOS (.45), GLOCK 40 MOS (10 mm), GLOCK 41 MOS (.45)
- Plate
- MOS Plate 05GLOCK factory
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- M3Not in GLOCK's plate set, which holds the plate screws only. GLOCK says to fit the optic as its maker directs, with screws that do not come through the 2.5 mm plate.
- Plate torque
- 13.1 in-lb (1.5 Nm)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
GLOCK MOS — standard & full size
Plate Adapter plate required
12 slides: GLOCK 19 Gen5 MOS, GLOCK 17 Gen5 MOS, GLOCK 45 Gen5 MOS, GLOCK 47 Gen5 MOS, GLOCK 49 Gen5 MOS, GLOCK 19X MOS, GLOCK 34 Gen5 MOS, GLOCK 26 Gen5 MOS, GLOCK 17 / 19 / 34 Gen4 MOS, GLOCK 22 / 23 Gen5 MOS (.40), GLOCK 35 Gen5 MOS (.40), GLOCK 44 MOS (.22 LR)
- Plate
- MOS Plate 01GLOCK factory; 1 other plate on the pair pages
- Plate → slide
- M3Supplied with the pistol, in the box with the cover plate.
- Optic → plate
- M3Not in GLOCK's plate set, which holds the plate screws only. GLOCK says to fit the optic as its maker directs, with screws that do not come through the 2.5 mm plate.
- Plate torque
- 13.1 in-lb (1.5 Nm)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
HK VP9 / SFP9 OR plate system
Plate Adapter plate required
4 slides: Heckler & Koch VP9 Optics Ready, Heckler & Koch VP9 Match OR, Heckler & Koch VP9SK Optics Ready, Heckler & Koch SFP9 OR (European VP9)
- Plate
- HK Optics Plate #1 (50254261)HK factory
- Plate → slide
- M4The two screws that hold the cover plate on the slide, reused for the plate (HK sells spares, part 50947116, and says to replace them after 2,000 rounds).
- Optic → plate
- per plate maker, not on file hereNot stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying.
- Plate torque
- 2 Nm (17.7 in-lb, converted)
- Optic torque
- per the optic maker (HK's manual gives no figure)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Plate system — fitment not published
Plate Verify Adapter plate required
3 slides: Walther WMP, Ruger American Pistol Competition, Rost Martin RM1S
- Plate
- Ask the maker → Docter familyUnconfirmed
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Rear-sight dovetail mount
Plate Dovetail mount required
2 slides: CZ P-07 / P-09 (standard, no optic cut), CZ 75 / SP-01 / Shadow 2 (non-OR)
- Plate
- Dovetail mount → RMR / C-More / Docter (type C)EGW
- Mount → dovetail
- set by the slideSupplied with the mount.
- Optic → mount
- M3 / #4-40 by modelSupplied with the plate, not the optic.
- Plate torque
- per mount instructions
- Optic torque
- 15 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Brass drift or sight pusher, Witness-mark paint or lacquer
- To mount
- $335–535approximate street prices, September 2026
Rost Martin metal optic plate system
Plate Adapter plate required
Slide: Rost Martin RM1C
- Plate
- Docter / Noblex metal optic plateRost Martin
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
S&W M&P C.O.R.E. / Optics Ready
Plate Fits on the plate in the box
8 slides: Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Smith & Wesson M&P9 M2.0 Compact Optics Ready, Smith & Wesson M&P9 M2.0 Metal, Smith & Wesson Performance Center M&P9 M2.0 Metal / Spec Series, Smith & Wesson M&P10mm M2.0 Optics Ready, Smith & Wesson M&P9 C.O.R.E. (pre-M2.0), Smith & Wesson M&P Carry Comp, Smith & Wesson M&P Competitor
- Plate
- C.O.R.E. Plate 3 (Docter family)S&W factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $300–450approximate street prices, September 2026
Taurus T.O.R.O. plate system
Plate Verify Adapter plate required
2 slides: Taurus G3 TORO / G3X TORO, Taurus G3C TORO / G3X TORO
- Plate
- T.O.R.O. Plate #1Taurus factory; 2 other plates on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $313–475approximate street prices, September 2026
Walther PDP 1.0 optic cut
Plate Adapter plate required
7 slides: Walther PDP Full Size (1.0), Walther PDP Compact (1.0), Walther PDP F-Series, Walther PDP Pro SD, Walther PDP Pro, Walther PDP Steel Frame, Walther PDP Compact F-Series
- Plate
- PDP 1.0 → Docter / VenomWalther factory
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- approximately 2 Nm (17.7 in-lb)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Walther PDP 2.0 optic cut
Plate Adapter plate required
2 slides: Walther PDP 2.0 Full Size, Walther PDP 2.0 Compact
- Plate
- PDP 2.0 → Docter / VenomC&H Precision
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- 4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Walther Q4 SF / Q5 Match SF optic cut
Plate Adapter plate required
2 slides: Walther Q5 Match SF, Walther Q4 SF Optics Ready
- Plate
- Q-series → Docter / VenomEGW; 1 other plate on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $325–510approximate street prices, September 2026
Steps and safety: installing a red dot, from the makers' manuals. Mounting an optic is gunsmithing; confirm the pistol is unloaded first. Screw length is never listed here because it depends on the whole stack: each pair's build sheet has a calculator that works from your own caliper readings.