Home / Optics / Olight Osight K / Moving it between pistols

Moving the Olight Osight K between pistols

Page last updated . Data compiled September 2026 by Andrew Terrebonne.

You already own it. Here is what changes from one slide to the next: the plate, the screw thread at each joint, the torque, the tools and any thread trap. 28 kinds of slide, covering 99 pistols, grouped by how the optic mounts and then alphabetically. Nothing is ranked. The Olight Osight K page has its specs and the per-pair answers.

The screws are not the same on every slideAcross these slides the optic's screws go into 4 different threads (#6-32, 4-40, M3, M4), and the screws from one pistol's box are often wrong for the next. Check the thread for the slide in front of you, and start every screw by hand.

14 of the 28 blocks have a figure marked not on file: no maker publishes it where this site could find it, so the plate maker or a gunsmith is the source. How the data is checked.

Mounts straight to the slide

CZ Nocturne direct cut

Direct Direct mount

2 slides: CZ P-09 Nocturne / P-09C Nocturne, CZ P-07 Nocturne

Optic → slide
M3, M4 or #6-32, by opticSupplied with the optic.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

CZ Shadow 2 Carry direct cut (Shield RMSc and Holosun K)

Direct (cross-fit) Direct mount — cross-compatible

Slide: CZ Shadow 2 Carry

Optic → slide
M3, M4 or #6-32, by opticSupplied with the optic.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

GLOCK Slimline MOS-K

Direct Direct mount

Slide: GLOCK 43X / 48 MOS-K

Optic → slide
M3Check the optic's box for M3 screws; buy a set if it has none.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026
Thread trapTapped M3, not the M4 of the earlier Slimline MOS. The two slim GLOCK cuts look alike but take different screws; mixing them up is the most common cross-threading mistake on slim GLOCKs. Screws in the box vary by Holosun K model. This slide takes M3; check yours match before fitting.

RMSc-pattern direct cut

Direct (cross-fit) Direct mount — cross-compatible

24 slides: Smith & Wesson M&P 22 Magnum, Smith & Wesson CSX E-Series Optics Ready, Springfield Armory XD-S Mod.2 OSP, Canik METE MC9 / MC9L, FN Reflex MRD, Beretta APX A1 Carry, Ruger MAX-9, Ruger Ruger-5.7 Optics Ready, Taurus TX22 Compact, Staccato CS, Palmetto State Armory Dagger Micro, Palmetto State Armory 5.7 Rock Optics Ready, Mossberg MC2sc Optic Ready, IWI Masada Slim, Archon Firearms Type B / Type D OR, Girsan Witness2311, Tisas Carry DS / Duty DS, Stoeger STR-9MC, SCCY CPX RDR / DVG-1 RDR, Avidity Arms PD10, Rock Island Armory STK100, Bersa BP9CC OR, Smith & Wesson M&P Shield Plus Carry Comp, Canik METE MC9 Prime

Optic → slide
M3, M4 or #6-32, by opticSupplied with the optic.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026
Thread trapNo screw thread is on file for this slide, and slim cuts from different makers are tapped M3, M4 or #6-32. Start each screw by hand. If it binds, stop and check the pistol's manual or ask the maker.

S&W M&P 5.7 direct cut

Direct (cross-fit) Direct mount — cross-compatible

Slide: Smith & Wesson M&P 5.7

Optic → slide
#6-32 × 1/2 inCheck the optic's box for #6-32 screws; buy a set if it has none.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026
Thread trapDocumented as #6-32 × 1/2 in for Holosun K optics, a different thread from either GLOCK slim cut despite the similar footprint. Screws in the box vary by Holosun K model. This slide takes #6-32; check yours match before fitting.

Shadow Systems CR920 optic cut (RMSc pattern)

Direct (cross-fit) Direct mount — cross-compatible

Slide: Shadow Systems CR920 / CR920P

Optic → slide
Not on file: Shadow Systems supplies the screws in its optic kitShadow's optic kit, taped inside the pistol box lid. This optic is not in Shadow's optic-fit table: try the kit's screws until a set goes through the optic and tightens against its body without bottoming out.
Optic torque
10–20 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

Shadow Systems multi-optic cut (MR920, DR920, XR920)

Direct (cross-fit) Direct mount — cross-compatible

5 slides: Shadow Systems MR920, Shadow Systems DR920 / DR920P, Shadow Systems XR920 / XR920P, Shadow Systems Foundation Series, Shadow Systems MR920 Elite / Combat

Optic → slide
Not on file: Shadow Systems supplies the screws in its optic kitShadow's optic kit, taped inside the pistol box lid. This optic is not in Shadow's optic-fit table: try the kit's screws until a set goes through the optic and tightens against its body without bottoming out.
Optic torque
10–20 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

SIG P322 optic cut (RMSc pattern)

Direct (cross-fit) Direct mount — cross-compatible

Slide: SIG Sauer P322 / P322 Comp

Optic → slide
M3 × 0.5Check the optic's box for M3 screws; buy a set if it has none.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026
Thread trapSIG lists M3 × 0.5 screws for the P322, the same as early P365 slides. Screws in the box vary by Holosun K model. This slide takes M3; check yours match before fitting.

SIG P365 optic cut (RMSc pattern)

Direct (cross-fit) Direct mount — cross-compatible

7 slides: SIG Sauer P365 Optics Ready, SIG Sauer P365X, SIG Sauer P365XL, SIG Sauer P365-XMACRO / XMACRO Comp, SIG Sauer P365-AXG Legion, SIG Sauer P365-380, SIG Sauer P365 Fuse

Optic → slide
M3 × 0.5 or M4 × 0.7, by slideCheck your slide's thread, then buy screws to match.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026
Thread trapSIG tapped early P365 optic cuts M3 × 0.5 and later ones M4 × 0.7, and sells a screw set for each. The model name doesn't tell you which slide you have; SIG's screw-set page shows both. Your slide is tapped M3 or M4. No date or serial-number rule from the maker says which a slide has, so there is no shortcut. To tell which, turn an M3 screw in by hand only: if it catches and runs in smoothly, the slide is M3; if it wobbles and never bites, the slide is M4. Never put a driver on a screw that won't start by hand. Screws in the box vary by Holosun K model.

Springfield Echelon VIS

Direct (cross-fit) Direct mount — cross-compatible

3 slides: Springfield Armory Echelon, Springfield Armory Echelon 4.0C, Springfield Armory Echelon Compact 4.5C

Pins → slide
No thread — interference fitPin set 1, the set Springfield's chart gives the optics it names on this footprint. This optic is not on the chart.
Optic → slide
M3, M4 or #6-32, by opticSupplied with the optic.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Tweezers, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

Taurus 856 T.O.R.O. revolver cut

Direct (cross-fit) Direct mount — cross-compatible

Slide: Taurus Defender 856 TORO

Optic → slide
M3, M4 or #6-32, by opticSupplied with the optic.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

Taurus GX4 T.O.R.O. direct cut

Direct (cross-fit) Direct mount — cross-compatible

3 slides: Taurus GX4 TORO / GX4XL, Taurus GX4 Carry TORO, Taurus GX4 Graphene TORO

Optic → slide
M4 × 0.7Check the optic's box for M4 screws; buy a set if it has none.
Optic torque
8.2 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026
Thread trapTaurus's manual says to use the optic's own screws only if they are M4 × 0.7 mm, with at least 4 threads of engagement in the slide; otherwise use the two screws that came with the slide cover. Screws in the box vary by Holosun K model. This slide takes M4; check yours match before fitting.

Taurus Judge T.O.R.O. revolver cut

Direct (cross-fit) Direct mount — cross-compatible

Slide: Taurus Judge TORO / Raging Hunter

Optic → slide
M3, M4 or #6-32, by opticSupplied with the optic.
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
To mount
$60–150approximate street prices, September 2026

Mounts on a plate

Arex Delta Gen.2 plate system

Plate Adapter plate required

Slide: Arex Delta Gen.2

Plate
Delta Gen.2 optic plate — type 5Aftermarket
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Beretta 80X Cheetah plate system

Plate Adapter plate required

Slide: Beretta 80X Cheetah

Plate
80X Cheetah → Holosun KBeretta factory
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

CZ P-10 OR plate system

Plate Adapter plate required

3 slides: CZ P-10 C Optics Ready, CZ P-10 F Optics Ready, CZ P-10 S Optics Ready

Plate
P-10 OR → RMSc / Holosun KCZ factory
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
1.3 Nm (11.5 in-lb)
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$120–245approximate street prices, September 2026

CZ Shadow 2 OR plate system

Plate Adapter plate required

2 slides: CZ Shadow 2 Optics Ready, CZ Shadow 2 Compact Optics Ready

Plate
Shadow 2 OR → RMSc / Holosun KCZ factory
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$120–245approximate street prices, September 2026

FN MRD plate system

Plate Adapter plate required

5 slides: FN 509 MRD / Tactical, FN 509 Midsize MRD / Compact MRD, FN 509 LS Edge, FN 510 / 545 MRD, FN 509 CC Edge

Plate
FN MRD → Holosun K / EPSC&H Precision
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

GLOCK Gen6 ORS

Plate Adapter plate required

Slide: GLOCK 17 / 19 / 45 Gen6 (ORS)

Plate
Gen 6 MIL/LEO → Holosun 407K / 507K / SIG ROMEOZero / Olight Osight K, SC&H Precision
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
M4Supplied with the plate, not the optic.
Plate torque
per plate maker, not on file here
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$120–245approximate street prices, September 2026

GLOCK MOS — 10 mm / .45 frames

Plate Adapter plate required

4 slides: GLOCK 20 Gen5 MOS (10 mm), GLOCK 21 Gen5 MOS (.45), GLOCK 40 MOS (10 mm), GLOCK 41 MOS (.45)

Plate
V4 MIL/LEO (large frame)C&H Precision
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate maker, not on file here (13.1 in-lb (1.5 Nm) is the slide maker's figure for its own plates, not this one)
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

GLOCK MOS — standard & full size

Plate Adapter plate required

12 slides: GLOCK 19 Gen5 MOS, GLOCK 17 Gen5 MOS, GLOCK 45 Gen5 MOS, GLOCK 47 Gen5 MOS, GLOCK 49 Gen5 MOS, GLOCK 19X MOS, GLOCK 34 Gen5 MOS, GLOCK 26 Gen5 MOS, GLOCK 17 / 19 / 34 Gen4 MOS, GLOCK 22 / 23 Gen5 MOS (.40), GLOCK 35 Gen5 MOS (.40), GLOCK 44 MOS (.22 LR)

Plate
V4 MIL/LEO (one SKU per footprint)C&H Precision
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate maker, not on file here (13.1 in-lb (1.5 Nm) is the slide maker's figure for its own plates, not this one)
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Kimber KDS9c plate system

Plate Adapter plate required

Slide: Kimber KDS9c

Plate
KDS9c → RMSc / Holosun K (incl. rear sight)Kimber factory
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Kimber R7 Mako plate system

Plate Adapter plate required

Slide: Kimber R7 Mako

Plate
R7 Mako → Holosun 407K / 507K / Osight SC&H Precision; 1 other plate on the pair pages
Plate → slide
#6-32Supplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Rear-sight dovetail mount

Plate Dovetail mount required

2 slides: CZ P-07 / P-09 (standard, no optic cut), CZ 75 / SP-01 / Shadow 2 (non-OR)

Plate
Dovetail mount → Holosun KEGW
Mount → dovetail
set by the slideSupplied with the mount.
Optic → mount
M3, M4 or #6-32, by opticSupplied with the plate, not the optic.
Plate torque
per mount instructions
Optic torque
15 in-lb
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Brass drift or sight pusher, Witness-mark paint or lacquer
To mount
$95–235approximate street prices, September 2026

S&W M&P C.O.R.E. / Optics Ready

Plate Adapter plate required

8 slides: Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Smith & Wesson M&P9 M2.0 Compact Optics Ready, Smith & Wesson M&P9 M2.0 Metal, Smith & Wesson Performance Center M&P9 M2.0 Metal / Spec Series, Smith & Wesson M&P10mm M2.0 Optics Ready, Smith & Wesson M&P9 C.O.R.E. (pre-M2.0), Smith & Wesson M&P Carry Comp, Smith & Wesson M&P Competitor

Plate
M&P 2.0 → Holosun KC&H Precision; 2 other plates on the pair pages
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Springfield AOS

Plate Adapter plate required

3 slides: Springfield Armory Prodigy (1911 DS), Springfield Armory 1911 DS Operator AOS, Springfield Armory XD-M Elite OSP

Plate
AOS → Holosun K / EPSC&H Precision
Plate → slide
#6-48Supplied with the plate.
Optic → plate
4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Taurus T.O.R.O. plate system

Plate Verify Adapter plate required

2 slides: Taurus G3 TORO / G3X TORO, Taurus G3C TORO / G3X TORO

Plate
T.O.R.O. → Holosun 407K / 507KC&H Precision; 1 other plate on the pair pages
Plate → slide
per plate maker, not on file hereSupplied with the plate.
Optic → plate
per plate maker, not on file hereSupplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Walther PDP 2.0 optic cut

Plate Adapter plate required

2 slides: Walther PDP 2.0 Full Size, Walther PDP 2.0 Compact

Plate
PDP 2.0 → Holosun K / EPSC&H Precision
Plate → slide
M3Supplied with the plate.
Optic → plate
4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
Plate torque
per plate instructions
Optic torque
per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
Tools
Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
To mount
$85–210approximate street prices, September 2026

Steps and safety: installing a red dot, from the makers' manuals. Mounting an optic is gunsmithing; confirm the pistol is unloaded first. Screw length is never listed here because it depends on the whole stack: each pair's build sheet has a calculator that works from your own caliper readings.

Something on this page wrong? Tell us what it should be, and include a source: nothing changes without one.