Moving the Holosun 407C X2 between pistols
Page last updated . Data compiled September 2026 by Andrew Terrebonne.
You already own it. Here is what changes from one slide to the next: the plate, the screw thread at each joint, the torque, the tools and any thread trap. 34 kinds of slide, covering 106 pistols, grouped by how the optic mounts and then alphabetically. Nothing is ranked. The Holosun 407C X2 page has its specs and the per-pair answers.
28 of the 34 blocks have a figure marked not on file: no maker publishes it where this site could find it, so the plate maker or a gunsmith is the source. How the data is checked.
Mounts straight to the slide
PSA Dagger RMR cut
Direct Direct mount
Slide: Palmetto State Armory Dagger Full Size / Compact (RMR cut)
- Optic → slide
- #6-32Supplied with the optic.
- Optic torque
- 15 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Ruger RXM direct-mount optic cut (RMR, DPP, RMSc)
Direct Direct mount
2 slides: Ruger RXM, Ruger RXM Compact
- Pins → slide
- No thread — slip fit2 of the dowel pins in the envelope supplied with the pistol, for the Trijicon RMR pattern, per Ruger's manual.
- Optic → slide
- #6-32 UNCSupplied with the optic, torqued to the optic maker's figure, per Ruger's manual.
- Optic torque
- 15 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Shadow Systems multi-optic cut (MR920, DR920, XR920)
Direct Direct mount
5 slides: Shadow Systems MR920, Shadow Systems DR920 / DR920P, Shadow Systems XR920 / XR920P, Shadow Systems Foundation Series, Shadow Systems MR920 Elite / Combat
- Optic → slide
- Not on file: Shadow Systems supplies the screws in its optic kitShadow's optic kit, taped inside the pistol box lid: screws 1 (V2/X2 models) in Shadow's optic-fit table; spacer A, at the rear of the recess, is optional.
- Optic torque
- 10–20 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Springfield Echelon VIS
Direct Direct mount
3 slides: Springfield Armory Echelon, Springfield Armory Echelon 4.0C, Springfield Armory Echelon Compact 4.5C
- Pins → slide
- No thread — interference fitPin set 1, the set Springfield's chart gives the optics it names on this footprint. This optic is not on the chart.
- Optic → slide
- #6-32Supplied with the optic.
- Optic torque
- 15 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, Tweezers, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Mounts on a plate
Arex Delta Gen.2 plate system
Plate Adapter plate required
Slide: Arex Delta Gen.2
- Plate
- Delta Gen.2 optic plate — type 2Aftermarket
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Arex Zero 1 Tactical ROR plate system
Plate Adapter plate required
Slide: Arex Zero 1 Tactical
- Plate
- Zero 1 Tactical ROR plate — TrijiconAftermarket
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Beretta 92X / M9A4 plate system
Plate Adapter plate required
7 slides: Beretta 92X RDO, Beretta 92X / 92XI / 92XI SAO, Beretta 92XI Squalo, Beretta 92 GTS, Beretta M9A4, Beretta 92FS X Performance OR, Beretta 94X Performance
- Plate
- 92X / M9A4 → Trijicon RMRBeretta factory; 1 other plate on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Beretta APX A1 / APX RDO plate system
Plate Adapter plate required
3 slides: Beretta APX A1 Full Size, Beretta APX A1 Compact, Beretta APX RDO
- Plate
- APX A1 / RDO → Trijicon RMRBeretta factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Canik SFx Rival optic interface plates
Plate Fits on the plate in the box
Slide: Canik SFx Rival / Rival-S
- Plate
- Canik interface R02 → RMRCanik factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Canik TP9 SFx optic interface plates
Plate Fits on the plate in the box
Slide: Canik TP9 SFx
- Plate
- Canik interface 02 → RMRCanik factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Canik TTI Combat optic interface plates
Plate Fits on the plate in the box
2 slides: Canik TTI Combat, Canik TTI Combat Master
- Plate
- Canik interface 03 → RMRCanik factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- #6-32The optic's own screws: Canik says to use only the #6-32 screws that came with the optic with this interface, not the M3 or M4 screws packed for other footprints.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
CZ P-10 OR plate system
Plate Adapter plate required
3 slides: CZ P-10 C Optics Ready, CZ P-10 F Optics Ready, CZ P-10 S Optics Ready
- Plate
- P-10 OR → RMRCZ factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- 1.3 Nm (11.5 in-lb)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $210–395approximate street prices, September 2026
CZ Shadow 2 OR plate system
Plate Adapter plate required
2 slides: CZ Shadow 2 Optics Ready, CZ Shadow 2 Compact Optics Ready
- Plate
- Shadow 2 OR → RMRCZ factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $210–395approximate street prices, September 2026
FN MRD plate system
Plate Fits on the plate in the box
5 slides: FN 509 MRD / Tactical, FN 509 Midsize MRD / Compact MRD, FN 509 LS Edge, FN 510 / 545 MRD, FN 509 CC Edge
- Plate
- FN MRD → RMRFN factory, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
GLOCK Gen6 ORS
Plate Fits on the plate in the box
Slide: GLOCK 17 / 19 / 45 Gen6 (ORS)
- Plate
- ORS Plate 02GLOCK factory, ships with the pistol; 1 other plate on the pair pages
- Plate → slide
- None: the plate has no screws of its ownNone: GLOCK's sheet has you seat the polymer plate in the slide and fit the optic through it. It says not to reuse the cover-plate screws to hold a plate.
- Optic → plate
- 6-32 UNC (into the slide, through the plate)Not in GLOCK's plate set. GLOCK's manual says to use the optic maker's own mounting screws.
- Plate torque
- None: GLOCK gives no plate screws or torque
- Optic torque
- per optic manual (GLOCK gives no figure)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
GLOCK MOS — 10 mm / .45 frames
Plate Fits on the plate in the box
4 slides: GLOCK 20 Gen5 MOS (10 mm), GLOCK 21 Gen5 MOS (.45), GLOCK 40 MOS (10 mm), GLOCK 41 MOS (.45)
- Plate
- MOS Plate 06GLOCK factory, ships with the pistol; 1 other plate on the pair pages
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- 6-32 UNCLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- 13.1 in-lb (1.5 Nm)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
GLOCK MOS — standard & full size
Plate Fits on the plate in the box
12 slides: GLOCK 19 Gen5 MOS, GLOCK 17 Gen5 MOS, GLOCK 45 Gen5 MOS, GLOCK 47 Gen5 MOS, GLOCK 49 Gen5 MOS, GLOCK 19X MOS, GLOCK 34 Gen5 MOS, GLOCK 26 Gen5 MOS, GLOCK 17 / 19 / 34 Gen4 MOS, GLOCK 22 / 23 Gen5 MOS (.40), GLOCK 35 Gen5 MOS (.40), GLOCK 44 MOS (.22 LR)
- Plate
- MOS Plate 02GLOCK factory, ships with the pistol; 2 other plates on the pair pages
- Plate → slide
- M3Supplied with the pistol, in the box with the cover plate.
- Optic → plate
- 6-32 UNCLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- 13.1 in-lb (1.5 Nm)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
GLOCK Slimline MOS (43X / 48)
Plate Adapter plate required
3 slides: GLOCK 43X MOS, GLOCK 48 MOS, GLOCK 43X / 48 Rail MOS
- Plate
- V4 MIL/LEO 43X / 48 MOS → Trijicon RMR / SRO / Holosun 407C / 507C / 508TC&H Precision; 1 other plate on the pair pages
- Plate → slide
- M4Supplied with the plate.
- Optic → plate
- 4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
- Plate torque
- per plate maker
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
HK VP9 / SFP9 OR plate system
Plate Adapter plate required
4 slides: Heckler & Koch VP9 Optics Ready, Heckler & Koch VP9 Match OR, Heckler & Koch VP9SK Optics Ready, Heckler & Koch SFP9 OR (European VP9)
- Plate
- HK Optics Plate #2 (50254262)HK factory; 1 other plate on the pair pages
- Plate → slide
- M4The two screws that hold the cover plate on the slide, reused for the plate (HK sells spares, part 50947116, and says to replace them after 2,000 rounds).
- Optic → plate
- per plate maker, not on file hereNot stated in HK's manual or plate listing: check with HK USA, or the optic's box, before buying.
- Plate torque
- 2 Nm (17.7 in-lb, converted)
- Optic torque
- per the optic maker (HK's manual gives no figure)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Plate system — fitment not published
Plate Verify Adapter plate required
3 slides: Walther WMP, Ruger American Pistol Competition, Rost Martin RM1S
- Plate
- Ask the maker → RMR familyUnconfirmed
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Rear-sight dovetail mount
Plate Dovetail mount required
2 slides: CZ P-07 / P-09 (standard, no optic cut), CZ 75 / SP-01 / Shadow 2 (non-OR)
- Plate
- Dovetail mount → RMR / C-More / Docter (type C)EGW
- Mount → dovetail
- set by the slideSupplied with the mount.
- Optic → mount
- #6-32Supplied with the plate, not the optic.
- Plate torque
- per mount instructions
- Optic torque
- 15 in-lb
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Brass drift or sight pusher, Witness-mark paint or lacquer
- To mount
- $185–385approximate street prices, September 2026
Rost Martin metal optic plate system
Plate Fits on the plate in the box
Slide: Rost Martin RM1C
- Plate
- RMR footprint optic plate kitRost Martin, ships with the pistol
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
S&W M&P C.O.R.E. / Optics Ready
Plate Fits on the plate in the box
8 slides: Smith & Wesson M&P9 M2.0 Optics Ready (4.25 / 4.6 / 5 in), Smith & Wesson M&P9 M2.0 Compact Optics Ready, Smith & Wesson M&P9 M2.0 Metal, Smith & Wesson Performance Center M&P9 M2.0 Metal / Spec Series, Smith & Wesson M&P10mm M2.0 Optics Ready, Smith & Wesson M&P9 C.O.R.E. (pre-M2.0), Smith & Wesson M&P Carry Comp, Smith & Wesson M&P Competitor
- Plate
- C.O.R.E. Plate 1 (RMR family)S&W factory, ships with the pistol; 2 other plates on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereLook in the pistol's box, with the plates. If there are none, buy a pair made for this plate.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $150–300approximate street prices, September 2026
Shadow Systems CR920 optic cut (RMSc pattern)
Plate Adapter plate required
Slide: Shadow Systems CR920 / CR920P
- Plate
- CR920 → Trijicon RMR / SRO / Holosun CC&H Precision
- Plate → slide
- #6-40Supplied with the plate.
- Optic → plate
- 4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
SIG P320 optic cut (Romeo1Pro pattern)
Plate Adapter plate required
7 slides: SIG Sauer P320 X-Carry, SIG Sauer P320 XCompact, SIG Sauer P320 XFive Legion, SIG Sauer P320 XTen, SIG Sauer P320 AXG Legion / AXG Pro, SIG Sauer P320 Spectre Comp, SIG Sauer P320-M17 / M18
- Plate
- P320 → RMR / SRO / RCR / Holosun CC&H Precision
- Plate → slide
- M4 × 0.7Supplied with the plate.
- Optic → plate
- #6-40Supplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
SIG Romeo1 cut (P226 / P229 RX Legion)
Plate Adapter plate required
Slide: SIG Sauer P226 / P229 Legion RX
- Plate
- Romeo1 → RMR / HolosunC&H Precision
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Springfield AOS
Plate Adapter plate required
3 slides: Springfield Armory Prodigy (1911 DS), Springfield Armory 1911 DS Operator AOS, Springfield Armory XD-M Elite OSP
- Plate
- AOS → RMR / SROSpringfield factory
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Springfield Hellcat OSP cut (Micro footprint)
Plate Adapter plate required
4 slides: Springfield Armory Hellcat OSP, Springfield Armory Hellcat Pro, Springfield Armory Hellcat RDP, Springfield Armory Hellcat Pro Comp OSP
- Plate
- Hellcat (RMSc footprint) → Trijicon RMR / SRO / Holosun 407C / 507C / 508TC&H Precision
- Plate → slide
- M4Supplied with the plate.
- Optic → plate
- 4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
- Plate torque
- per plate maker, not on file here
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Taurus 856 T.O.R.O. revolver cut
Plate Adapter plate required
Slide: Taurus Defender 856 TORO
- Plate
- Taurus 856 → RMR / SRO / Holosun 407C / 507C / 507Comp / 508TC&H Precision
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Taurus Judge T.O.R.O. revolver cut
Plate Adapter plate required
Slide: Taurus Judge TORO / Raging Hunter
- Plate
- Taurus Judge T.O.R.O. → RMR / RMR HD / SRO / Holosun 407C / 507C / 507Comp / 508TC&H Precision
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Taurus T.O.R.O. plate system
Plate Verify Adapter plate required
2 slides: Taurus G3 TORO / G3X TORO, Taurus G3C TORO / G3X TORO
- Plate
- T.O.R.O. Plate #2Taurus factory; 1 other plate on the pair pages
- Plate → slide
- per plate maker, not on file hereSupplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $163–325approximate street prices, September 2026
Walther PDP 1.0 optic cut
Plate Adapter plate required
7 slides: Walther PDP Full Size (1.0), Walther PDP Compact (1.0), Walther PDP F-Series, Walther PDP Pro SD, Walther PDP Pro, Walther PDP Steel Frame, Walther PDP Compact F-Series
- Plate
- PDP Gen1 optic plate, RMR footprint (2844079)Walther factory; 1 other plate on the pair pages
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- per plate maker, not on file hereSupplied with the plate, not the optic.
- Plate torque
- approximately 2 Nm (17.7 in-lb)
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Walther PDP 2.0 optic cut
Plate Adapter plate required
2 slides: Walther PDP 2.0 Full Size, Walther PDP 2.0 Compact
- Plate
- PDP 2.0 → Trijicon RMRC&H Precision
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- 4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Walther Q4 SF / Q5 Match SF optic cut
Plate Adapter plate required
2 slides: Walther Q5 Match SF, Walther Q4 SF Optics Ready
- Plate
- Q-series → Trijicon RMRC&H Precision
- Plate → slide
- M3Supplied with the plate.
- Optic → plate
- 4-40 (into the plate's T-nuts)Supplied with the plate, not the optic.
- Plate torque
- per plate instructions
- Optic torque
- per plate maker, not on file here (15 in-lb is the optic maker's figure for mounting it straight on a slide)
- Tools
- Torque wrench, Driver bits, Calipers, Degreaser, A parts tray, Witness-mark paint or lacquer
- To mount
- $175–360approximate street prices, September 2026
Steps and safety: installing a red dot, from the makers' manuals. Mounting an optic is gunsmithing; confirm the pistol is unloaded first. Screw length is never listed here because it depends on the whole stack: each pair's build sheet has a calculator that works from your own caliper readings.